m3d pro
71563 3d models found related to m3d pro.thingiverse
Filament clip for the M3D Pro. ...Snaps onto the extruder braided cable and guides filament into the external filament port.
thingiverse
I had trouble with dust on my filament, so I created a filter holder for the m3d pro using a spool holder mount and a generic filter holder.
thingiverse
Here is a new version of https://www.thingiverse.com/thing:817979 This one fits the M3D PRO. I redesigned the guide to fit the bigger frame of the PRO. Same concept, just BIGGER,.... ...
thingiverse
Brackets that secure an alternative 200x200 boroscillicate bed (with optional BuildTak Flex plate). ... Fits snugly into existing M3D Pro without any alterations. ...
thingiverse
This is a side mounted large spool holder for the M3D pro. ...Had loads of issues with worktop spool holders, this one feeds from above.
thingiverse
... Holder by ilikesanta. ... This version works for the M3D Pro. Note when I took the picture, I had two right arms one from when I was testing v2 and I just used a dowel as the shaft. ... NOTE: Make sure to print with the arm flat on the base!
thingiverse
I made this to aid in lubing the rails of the M3D Pro. I used a piece of an unmatched sock and hot glued the ends to it using a pencil to hold the cloth in place. ... It is supposed to make applying the recommended teflon lubricant easier.
thingiverse
### About A simple 40mm fan mount to cool the extruder on an M3D Pro (also works on the M3D Micro, but isn't designed for it). ### Fan Selection Don't get a "high airflow" fan. A cheap toy fan that moves 2-4 CFM will do very nicely. The...
cults3d
This spool holder is intended for the M3D Pro printer, and sits on top of the unit, above the extruder, and using the printer chassis as base. These are brackets only. Two sets are needed, one for each side, then simply add any dowel, rod or tubing...
thingiverse
This spool holder is intended for the M3D Pro printer, and sits on top of the unit, above the extruder, and using the printer chassis as base. These are brackets only. Two sets are needed, one for each side, then simply add any dowel, rod or...
thingiverse
Corner post holders (e.g. ...for filament spools) that fit M3D pro
thingiverse
Corner post holders (e.g. ...for filament spools) that fit M3D pro
thingiverse
This is a M3D PRO spool holder that fits almost all spools that I have. the height is 135mm high so it should fit any roll up to that size. EDIT 9/8/2017 Ive added a thicker trunk. After awhile heavier rolls would bend the holder. ...This one is 10mm...
myminifactory
First version of clips for external mounting of cooling fans for M3D Pro printer. Screw or glue your external fan onto the clips wich can be easily mounted and unmounted to provide extra airflow when printing, to get a better result.I will be...
thingiverse
Adjustabel spool for M3D PRO, for internal use (over the bed)
thingiverse
Customized version of http://www.thingiverse.com/thing:2383517 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=2383517
thingiverse
Customized version of https://www.thingiverse.com/thing:38096 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=38096
thingiverse
Customized version of http://www.thingiverse.com/thing:2383517 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=2383517
thingiverse
Customized version of http://www.thingiverse.com/thing:2383517 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=2383517
thingiverse
I wanted a side mount spool holder for my pro, Found this one but it was too small for my big 3rd party spools, so I modified it. https://www.thingiverse.com/thing:2432747 I created 2 sizes of shaft to accommodate 3in wide or 4in wide spools,...
thingiverse
Customized version of https://www.thingiverse.com/thing:2383517 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2383517
cults3d
Quick edit of Rodneyk's thing to make the centre hole 13 mm to accommodate the 12mm wood dowel I use in my spool holder. There was no need to edit the nut, but I include the original here for completeness. ... Thanks for the wonderful thing rodneyk.
thingiverse
Customized version of https://www.thingiverse.com/thing:2383517 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2383517
thingiverse
Customized version of https://www.thingiverse.com/thing:2383517 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2383517
thingiverse
Quick edit of Rodneyk's thing to make the centre hole 13 mm to accommodate the 12mm wood dowel I use in my spool holder. There was no need to edit the nut, but I include the original here for completeness. ... Thanks for the wonderful thing rodneyk.
thingiverse
Customized version of http://www.thingiverse.com/thing:2383517 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=2383517
thingiverse
Customized version of http://www.thingiverse.com/thing:2383517 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=2383517
thingiverse
Customized version of http://www.thingiverse.com/thing:2383517 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=2383517
thingiverse
Customized version of http://www.thingiverse.com/thing:2383517 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=2383517