m4 block 3 3d models

MagRel Block M4 hole (3,6mm) Nose Full

This is a replaceable gas block for M4 airsoft guns. ...This gas block was designed for those people who like using red dots without the iron sight and don'w want to cut it of from the original gas block.

This is a gas block with rails designed for an airsoft M4. This will fit a standard profile barrel with a .75" dia. I have not printed this yet so I'm not sure how it will come out. Instructions This should fit a standard profile M4 barrel. the...

A simple M4 3/16" spacer. ...Works well for mounting Raspberry Pis, Arduinos, relays, and similar PCB components slightly elevated.

Block 3 for EST I

I made this so i hopefully dont have to adjust the bedlevel anymore. ... (the screw will still rotate but the knob doesnt move up and down) You need to Pause the print at 6mm and insert the M4 Nuts.

... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=44421 Instructions Using the following options: hgrip = 5 dscrew = 4.35 shift = 89 dgrip = 20 hprotrus = 3 sscrewhead = 7.5 hscrewhead = 4 bevel = 1

Mp5 Delta Block for M4 (Retro Arms) HopUp Chamber

Block for extrusion 2020 2040 M4 without nut

This is my block

THIS IS MY THIRD BLOCK

Install front sight from airsoft gas block. Выкладываю как есть. Я не знаю, подойдет ли это на внешний ствол конкретно вашей М4. Печатал из ABS. Лишние отверстия для стевлоколоконных стержней или стальных шпилек. ... Мушку переставить со...

Need 2 x M4 Nuts and 2 x M4 bolts (16mm with hex head). ###### Clearance: Trough holes sized according to M4 normal fit (4.5mm). Clearance of 0.3mm for the bolt holder and nut holder on top of ISO max. 7mm and 8.1mm is used according to ISO. In...

M4/3 Rear Lens Cap

M4/3 Rear Lens Cap Category: Camera

6 mm outer diameter spacer, 4 mm inside diameter, 3.5mm length.

http://www.thingiverse.com/apps/customizer/run?thing_id=15633 Instructions Using the following options: gap = 0.3 nut = 8 offset = 2 trap = 2 wall = 1.6 boltHead = 7.2 shaft2 = 6.3 shaft1 = 6 bridge = 0.3 washer = 0 boltShaft = 4.3 length = 40...

http://www.thingiverse.com/apps/customizer/run?thing_id=713300 Instructions Using the following options: height = 9 cross_section = 0 screw_hole_diameter = 55 knurled_height = 70 nut_thickness = 3 nut_width = 7.8 nut_sides = 6 screw_hole_length = 100...

Trapezoid Block 3

1-2-3 Block

3-4-6 Block

Trapezoid Block 3

CSWA Trapazoid Block 3

Simple 1-2-3-Block

Ender-3 Fan block 3010 Fan * 3 M3 Nuts * 12 M3X16 Screws * 12 M3X10 Screws * 2

slidingblock requierd: M4 SW7 Nut washer up to 9mm, tickness 0.5mm

23 Hole 1-2-3 Block w/ 3/8" drilled holes and 3/8"-16 threaded holes

These are the 3D cartoon character designs from Mrs. ...Fasciale's Block 3 Art Class.

Block #3 from the Macalester College Mineralogy course activity on crystal systems and symmetry operations.

Just a model of a concrete block commonly used on the Caribbean. ...Its a 6 inches concrete block with 3 holes.