m4 stock and mp5k adaptor 3d models

I made this to replace the tank stock, on my Calico Jack with a standard M4 stock I had on-hand. The contact between the frame and the connector fits well and it is held in place by rigid internal extrusions. Note that the standard tabs that mount...

M4 or AR15 airsoft folding stock for airsoft. FOR AIRSOFT GUN ONLY! Stock mount 2 has a shoulder strap. Stock mount - does not have it. For assembly you will need: 1. 1. Spring 15mm long, outer diameter 10mm, thread thickness - 0.7-1.0mm - 1 piece.

Not being able to find the part online proved a real challenge, so I took matters into my own hands and designed a replacement - which turned out great!\nThe diameter of the main cylinder measures 20mm exactly.\nThe length of the curved portion of...

It is a replacement part like the m4 stock. See photo for the play. It is used to avoid dropping the battery. If you come in private on my mail, you will benefit from -20%. On this good print. ... link to my CYMA C0007 M4A1 AEG replica:...

Hi, Here is another stock for M4. The printing volume should match up with a 200mm x 200mm. You usually don't need to make support (not 100% sure) Feel free to let me know if it's printing well. ... Best, Iron.

This is a Milspec LE-style stock for airsoft M4 toys that requires a spring and one M3 screw to mount. I designed it specifically for use with my JTW HCC-2A, but it should work seamlessly with any AEG using a Milspec buffer tube. You can easily...

This is a custom PDW stock that can be installed on a standard M4 buffer tube. I designed it for my WE M4 GBBR, so the dimensions are somewhat "milspec". It uses the following components: 2 x 8mm rods - one of them will require 6mm slots cut into...

I designed it for my WE M4 GBBR so the dimensions are some what "milspec" It uses the following hardware: 2x 8mm rods , one of them you will have to cut 6mm slots for the locking mechanism 4x M3 screws to attach the cap for the locking mechanism to...

A small and simple device you can use on your buffer tube to limit the stock's travel.

Works for the JG g36 models (You will need the screw that holds the the m4 post to the rifle, however it might not be needed if you make the post tight to it) Edit: Added lock to the stock, glue it in the adapter after putting it on the gun as you...

This m249 stock adaptor is so strong that you dont need a metal one. ... There is a 4mm hole inside the stock so you only need a 5mm screw at the correct length to put your stock on it.

This model have -mp5k(gun) x1 -magazine x1 -bullet x4 -bullet(shell) x4

After an exhaustive search yielding no results, I pieced together this makeshift Stock adapter using Fusion 360 and drawing upon my extensive experience with CAD engineering. I've made some adjustments to ensure the stock adapter fits more snugly,...

Hello there! ...Check out this custom-made stock I created a few months back. It features a sturdy fixation that's secured by just one trusty M6 screw and a matching M6 nut. I hope you enjoy it, folks! ...- Iron.

Here are the details of this low-poly model: * Polygons: 2993 * Vertices: 3156 This Heckler & Koch MP5K features: * Created with Cinema 4D software. * Exportable in 3DS, C4D, FBX, and OBJ formats. * Layers are grouped and organized for easy editing....

Simply use an AEG m4 buffer tube with an M3 or M4 nut and make sure to tighten down firmly. I've found it to be very sturdy in PLA but would recommend PETG if you want to be extra safe. Please note that this is designed to be a very tight fit and as...

... Kingman Hammer 7. ...Additionally, the following cap-head hex screws are necessary: 1 M4 x 25mm and 1 M4 x 12mm (approximately, not confirmed). ...The dimensions appear to be accurate; however, final testing is required before considering it complete.

I Need to Get the Toystar M4 Buffer Tube, Along with an M5 Insert, Two M5 Bolts Measuring 35mm Each, and Two M5 Nuts. ...Using These Components Should Be a No-Brainer for Most People, But I'm Not So Sure About Everyone Else.

I'm excited to share my very first stock creation with you, and I'd love your feedback! ...It seems something isn't quite right with this one, but I'm stumped as to what it could be - can you help me figure out the issue?

I made clearances tighter and solidified it all to just fit more snug to the tube, as well as englarged and added a second rectangle to hold the tube, also enlarging the little V shaped part that holds the stock "open". While this will remove the...

I made clearances tighter and solidified it all to just fit more snug to the tube, as well as englarged and added a second rectangle to hold the tube, also enlarging the little V shaped part that holds the stock "open". While this will remove the...

To attach the adaptor, you'll need two short bolts and one of the stock fan bolts. Screw only the top bolt of the fan since it will fit snugly inside the adaptor. 26/02/2017 - Updated autolevel version, which could potentially cause interference...

I designed a bolt-on battery box/case specifically for a 3s 2.2Ah battery and a sopmod stock that fits snugly on a 109x34x27mm battery. You can find the exact battery I used here:...

mp5k

2020/2/06 Upload *.obj G&G - TR16 MBR 556WH - Design 3D Printed Battery Stock for Glock Share Stock for Larger Battery Please note the correct polarity of the battery! Important: Be aware of the correct battery polarity! ... Rubber band x 1 Screw M3 x...

This adaptor fits the Geeetech branded spool perfectly on a 32mm PVC tube used by Geeetech A10, A10M models and similar printers like Ender 3. It makes the spool roll smoothly on the stock holder. I added some lines to this design for easier sanding...

Hello, I've created a stock that's perfect for experimentation, but please don't attempt to 3D print it. The mechanism features a single M6 bolt holding the entire system together. ...Take care, Iron.

Convert G&G stock to accommodate Parkside battery. ... You must use the following sheets https://pt.aliexpress.com/item/32959524713.html?spm=a2g03.12010612.8148356.9.43ee191299D1RU to connect the battery to the Mosfet cables

enough room for a polarstar fcu and a 250-300mah lipo, nothing else

An adapter i created since i couldnt find it anywhere this is the first prototype so feel free to try and make it prettier. ... more to come