macbook bottom case 3d models
366536 3d models found related to macbook bottom case.thingiverse
When installing the bottom case, make sure you apply force in the right area to press the clip in. With provided Print settings, it's a good, tight fit. Printed in PETG plastic. PLA might work but the heat from the MacBook may warp the PLA over time....
thingiverse
One of the feet on my 13-inch retina mbp is missing. Looking up for a replacement or an alternative for some time, but the result is not so good: either is not available in China, or is not suitable for 13-rmbp. So I do it my self. The 13-rmbp's...
thingiverse
Optical Drive Case Salvaged the optical drive from an old macbook pro. Designed this case using Solidworks and bought an 13 pin sata connector from amazon. ...
thingiverse
Case Bottom Print Settings Printer Brand: MakerBot Printer: MakerBot Replicator Mini Notes: Size: 2.220" L x 1.283" W x 0.500" H
thingiverse
This is a cheap way to expend your Macbook Pro storage. ... Compatible with MacBook Pro (Retina) 13" (Late 2012 – Early 2015) You can buy every SD Card and take it apart to get the black memory chip as you can see at the photo.
prusaprinters
The cable is wrapped around it inside wall of the case, so it doesn't need to make any hard bends.The case itself is design to be as small as possible, considering the brick on the inside.It is very straight forward and easy to print, and just...
thingiverse
Speck cases ar cool, but 2017 model keep loosing back feet. ...Here you have a fast replacement that stays in place...
thingiverse
This is a work in progress for a carrying case for the MBP 14" 2021. I'm designing it with inner TPU inserts to protect the MBP and a cutout for a yubikey or other 2FA key that stays in the laptop. ... Haven't decided yet on the latching mechanism.
thingiverse
Bottom case for top case from this https://www.thingiverse.com/thing:4759948 Can used with hotswap pcb
thingiverse
M5Stack Case of Bottom with foot. ... Annyo means baby's foot in Japanese child's word.
thingiverse
Naze32 case 45x45 bottom Print Settings Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0,2 Infill: 50
thingiverse
Ho modificato il case_bottom_2 con feritoie laterali perché userò lattepanda in verticale. Ho aggiunto 2 fori nelle feritoie pulsante power per dare più flessibilità e ridurre rischio di rottura. ... Una seconda versione che riduce altezza del case...
thingiverse
Protective case for a Macbook Pro charger. ... Use supports
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=57281 Instructions Using the following options: _labelDepth = -0.3 _walls = 0.8 _base = 0.8 _fitGap = 0.1 _labelHeight = 8 _lipHeight = 2 _columns = 3 _labelFont = write/orbitron.dxf _labelText...
thingiverse
Case for electronic cigarette iQos with damaged cover. ...It allows the convenient closing and then loading.
thingiverse
Corne bottom for this top https://www.thingiverse.com/thing:4459741 Support hotswap socket
thingiverse
This is a case for the new V5 form factor Flip32+. The holes are 3mm, I just tapped them and use small screens to secure the board. ...As the board is quite protected in my quad I decided there was no need for a top cover.
thingiverse
Edit it online https://www.tinkercad.com/things/jk8jbFqGGls This is the lower half of the case for the UDRC. Attach the Rpi to this part with screws to the stand offs. Attach your UDRC to the upper half the same way. ...The two then go connect by...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=57281 Instructions Using the following options: _labelDepth = -0.3 _lipHeight = 2 _walls = 0.8 _fitGap = 0.1 _columns = 8 _rows = 2 _labelHeight = 8 _part = bottom _batteryDiameter = 14.6 _base...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=57281 Instructions Using the following options: _labelFont = write/orbitron.dxf _fitGap = 0.1 _labelText = _labelDepth = -0.3 _insideHeight = 30 _lipHeight = 2 _walls = 0.8 _labelHeight = 8...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=57281 Instructions Using the following options: _walls = 1.2 _rows = 2 _labelDepth = -0.3 _part = bottom _insideHeight = 30 _labelHeight = 8 _columns = 6 _labelFont = write/orbitron.dxf _base =...