macbook pro 13 inch stand 3d models
342027 3d models found related to macbook pro 13 inch stand.thingiverse
Designed for the MacBook Pro 13-inch 2017 model (14mm depth), might fit other models.
prusaprinters
Designed for the MacBook Pro 13-inch 2017 model (14mm depth), might fit other models. Category: Computer
thingiverse
After I printed it I realized that it is not suitable for Macbook Pro 13 inch. The laptops body was too thick to fit in. So I decided to create a version that fits Macbook Pro, is a little bit wider to add stability, and that uses less PLA. ... ...
thingiverse
Closed the gap in the original, made it thinner and adapted it to the macbook 13" with touchbar. ...Also added a small notch so it holds in the vent slots on the side of the macbook.
prusaprinters
Closed the gap in the original, made it thinner and adapted it to the macbook 13" with touchbar. ...Also added a small notch so it holds in the vent slots on the side of the macbook. Print Settings Printer: Print Rite DiY 3D Rafts: No Supports: No...
cults3d
Just a macbook stand/raiser angled to raise the height of the screen without too much angle so its not hard to type on the keyboard. pring sideways with some support on the bottom hood and the bridge between the upper and lower platforms. ... awaiting...
thingiverse
Just a macbook stand/raiser angled to raise the height of the screen without too much angle so its not hard to type on the keyboard. pring sideways with some support on the bottom hood and the bridge between the upper and lower platforms. ... awaiting...
thingiverse
Support (Stand) for 13" MacBook Pro using 12mm Carbon Fiber Rod
thingiverse
a small elegant stand for a 2019 macbook pro (13 inch). did sand and painted the stand, and used double sided type to attach it to the table. ... the unites in the photo are in mm.
cults3d
Laptop stand with folding feet. ... It's a stand for MacBook Pro 13-inch, sized for the 2018 generation but will work for any object of the same size.
thingiverse
You need to print two. ...Made these because i couldn't find proper ones. It fits perfectly my mid 2015 13 inch macbook pro retina. If you are looking for one to use while typing this one might be a bit high. ...So you should print the low version
thingiverse
Simple angled laptop stand for my Macbook Pro. Wanted a sharper angle to take up less deskroom. Will likely support other laptops -- the gap between vertical supports is 17mm. Inspired by [this design](https://www.thingiverse.com/thing:2597930)...
cults3d
Simple angled laptop stand for my Macbook Pro. Wanted a sharper angle to take up less deskroom. Will likely support other laptops -- the gap between vertical supports is 17mm. Inspired by this design but rebuilt in Tinkercad. I wanted to round out...
prusaprinters
Simple angled laptop stand for my Macbook Pro. Wanted a sharper angle to take up less deskroom. Will likely support other laptops -- the gap between vertical supports is 17mm.</p> <p>Inspired by <a...
thingiverse
INFO *** This desk stand is designed specifically to hold a 13 inch, 4th generation MacBook Pro. It will not fit earlier models, nor will it fit a 4th gen 15 inch model or a 13 inch model with a case. If you are interested in seeing stands of this...
thingiverse
Press fit / clip together Macbook Pro 13 inch laptop stand Designed with tight tolerances, the legs slide in and clip to the top plate for a rigid stylish laptop stand.
thingiverse
Very simple Macbook Pro 2020 (13-inch) stand. ...No supports needed.
thingiverse
A stand for Macbook Pro 13 inch. ...Mostly useful if you dock your macbook to a seperate keyboard/mouse/screen and want it kept open as a secondary screen.
cults3d
A stand for Macbook Pro 13 inch. ...Mostly useful if you dock your macbook to a seperate keyboard/mouse/screen and want it kept open as a secondary screen.
thingiverse
**MacBook Pro 13" stand** ---- * A nice stand/raiser for your MacBook Pro 13". * Designed for the 2020 M1 version, but should also fit others (including MacBook Air). * You will need two to four M5 threaded rods and a few M5 nuts (+ optional...
cults3d
MacBook Pro 13" stand A nice stand/raiser for your MacBook Pro 13". Designed for the 2020 M1 version, but should also fit others (including MacBook Air). You will need two to four M5 threaded rods and a few M5 nuts (+ optional sticky rubber feet).
thingiverse
I designed this stand for my wife's MacBook Pro 13 2014 model with Retina display. I would recommend that you print it out this file if you have the same model described above, but, if you want to this model fit in some of the new models or even...
cults3d
Macbook pro unibody stand from 2008 to 2012. UPDATE: I made another version. It is for the same macbook model. In case you need the other one, it is still available. ... To further care for the Macbook it is recommended to use a plush or similar to...
grabcad
13 inch 2015 model. I decided to challenge myself by attempting to model the MacBook in Fusion360. ...The MacBook is (obviously) not my original design, it belongs to Apple and is their product.
3docean
High quality model of Apple Macbook Air 13 inch with Retina display Will perfectly suit for middle distance shots and close-ups. • Nice topology (only tri and quad polygons) • Real-world sizes and proportions • The model is grouped for easy selection...
thingiverse
These were designed for a Macbook Pro 13 Inch but can be used on other models. YOU WILL NEED TO PRINT 2 Macbook lid can not be open and closeed fully whilst in the stand. ... This is a remix from https://www.thingiverse.com/thing:398515 Created...