macbook pro 13 stand 3d models
286924 3d models found related to macbook pro 13 stand.cults3d
MacBook Pro 13" stand A nice stand/raiser for your MacBook Pro 13". Designed for the 2020 M1 version, but should also fit others (including MacBook Air). You will need two to four M5 threaded rods and a few M5 nuts (+ optional sticky rubber feet).
thingiverse
**MacBook Pro 13" stand** ---- * A nice stand/raiser for your MacBook Pro 13". * Designed for the 2020 M1 version, but should also fit others (including MacBook Air). * You will need two to four M5 threaded rods and a few M5 nuts (+ optional...
thingiverse
I designed this stand for my wife's MacBook Pro 13 2014 model with Retina display. I would recommend that you print it out this file if you have the same model described above, but, if you want to this model fit in some of the new models or even...
cults3d
Macbook pro unibody stand from 2008 to 2012. UPDATE: I made another version. It is for the same macbook model. In case you need the other one, it is still available. ... To further care for the Macbook it is recommended to use a plush or similar to...
thingiverse
Einfacher Halter zum Aufstellen eines MacBook Pro 13" von Ende 2011. Druck dauerte circa. 5,5 Stunden Erste Veröffentlichung von einer eigenen Konstruktion. Da ich noch Anfänger bin, besteht durchaus Verbesserungspotential. Die...
thingiverse
Small project while I learn to model in Fusion. Part of the challenge was to cut the model in pieces that fit the small bed of the Select Mini. ...Front legs are attached to the rear leg using a couple of M3 screws.
thingiverse
... looked for something to use with my Thunderbolt Display. ...I found some laptop stand which were not very stable. This is my version! This thing is suitable for 4 mm wide plywood or any other 4mm wood you can cut with laser cutter. ... Happy Lasering!
thingiverse
My first 3D design work. ... It's for MacBook Pro 13.3 2017. Appreciate for your feedback. ... The stand angle is about 140 degrees
thingiverse
Press fit / clip together Macbook Pro 13 inch laptop stand Designed with tight tolerances, the legs slide in and clip to the top plate for a rigid stylish laptop stand.
thingiverse
Designed for the MacBook Pro 13-inch 2017 model (14mm depth), might fit other models.
prusaprinters
Designed for the MacBook Pro 13-inch 2017 model (14mm depth), might fit other models. Category: Computer
thingiverse
Slightly modified seongk's Macbook Pro Retina 15" Stand by reducing the height of the stands as well as the width of the overhangs. ...Trimmed the gap between the overhang to better fit the 13" MBP If you have a slippery desk, i suggest adding some...
thingiverse
After I printed it I realized that it is not suitable for Macbook Pro 13 inch. The laptops body was too thick to fit in. So I decided to create a version that fits Macbook Pro, is a little bit wider to add stability, and that uses less PLA. ... ...
thingiverse
The size is adjusted for the MacBook Pro 13. The two ledges on the lower sides are designed to do not protude out from the Mac shape and scratch your hands or arms, and the sides are smotted for this purpose. I printed it selecting 0.2mm layer...
thingiverse
Closed the gap in the original, made it thinner and adapted it to the macbook 13" with touchbar. ...Also added a small notch so it holds in the vent slots on the side of the macbook.
prusaprinters
Closed the gap in the original, made it thinner and adapted it to the macbook 13" with touchbar. ...Also added a small notch so it holds in the vent slots on the side of the macbook. Print Settings Printer: Print Rite DiY 3D Rafts: No Supports: No...
thingiverse
Laptop Stand for MacPro. ...Thickness of support is 8-12 mm Shell thickness 1.2 мм
thingiverse
steady and good looking no assembly needed might take around 1 day to print
cults3d
This is a simple stand for the 2019 Macbook Pro 13" if you are running your Macbook in a docked mode or clam mode. Saves a lot of room on your desktop. I printed a few of these to get it just right. You want something that can withstand desk bumps...
cults3d
This is a simple stand for the 2015 Macbook Pro 13" if you are running your Macbook in a docked mode or clam mode. Saves a lot of room on your desktop. I printed a few of these to get it just right. You want something that can withstand desk bumps...
prusaprinters
Hi, i designed a desktop stand for your MacBook, when using a monitor. fits MacBook Pro 13" 2016-2021, New MacBook Pro 14" -Settings recomendations:-Print with PLA/PETG, minimum 3 perimeters. -30% infill is fine-supports only needed...
grabcad
Laser cut laptop stand for a 13" Macbook Pro made of 1/4" cast acrylic.
thingiverse
Working for long periods on just a laptop causes bad posture and eye strain. ...Raising your laptop up and using an external keyboard helps reduce these problems. These riser stands will fit a 2017 MacBook Pro, and possibly other models.
thingiverse
For Apple Macbook pro retina 13" notebook stand Instructions
thingiverse
MacBook Pro 2018 13" Vertical Stand with open side for ventilation. ... Macbook Pro 2018 13" Halter mit seitlichen Lüftungsöffnungen.
thingiverse
Simple vertical stand for MacBook Pro 13 year 2011. ... Good print.
thingiverse
This is a vertical stand for the Macbook Pro 13-inch, 2017 with Touchbar model. Its designed to print on a small printer using very little material but holds the computer firmly without tipping over. Although its design allows sufficient air flow, I...