macbook pro holder 3d models
382768 3d models found related to macbook pro holder.thingiverse
A simple holder for the T1 SSD from Samsung. ...Place it on the top right corner of your MacBook and never worry about a dangling SSD. ... I suggest buying a 90* thunderbolt cable.
thingiverse
i could't find the right part from the original part, so I created it tips are always welcome :)
youmagine
This is a pretty tight fit by design. This way the HackRF does not slide all around. I printed this at %90 infill @ 1.5mm Z. It seems very tough. I am going to make a few tweaks and will upload them once done. ... But this is fully working as is!
cults3d
I wanted to have my phone right next to my computer screen but I could never get it to stay standing where it wasn't in the way but it would always die on me so I designed this holder that sits on the corner of my MacBook pro to hold my iPhone 12 pro...
thingiverse
Model made by @villekl is for MacBook Pro Retina (Early 2015) which has 0.71 inch (1.8 cm) height. I have MacBook Pro (Early 2011) which has 0.95 inch (2.41 cm) height. ... So I made a remix of original @villekl model just by stretching it to needed...
thingiverse
... the display is the highest speed that is set to "0" parameter of "edge_r" is when you want to preview. ("fn $ = 16/32" also change the speed up) [macbook_holder_v4_215.stl] => slot spacing 21.5mm [macbook_holder_v4_265.stl] => slot spacing 26.5mm
pinshape
SummaryThese can be used to store MB Pro under a table. Print two of each and srew in place. I suggest putting little pieces of protective tape on the edges that touch the computer. Print the corner pieces upright with one of the solid walls to the...
thingiverse
These can be used to store MB Pro under a table. Print two of each and srew in place. I suggest putting little pieces of protective tape on the edges that touch the computer. Print the corner pieces upright with one of the solid walls to the bed.
thingiverse
The Macbook Pro slot width as designed is 18.2mm, change scale for any other computer. The Macbook Air slotwidth is 12mm. Print Settings Printer Brand: LulzBot ...
thingiverse
A simple holder for the MacBook Pro from mid 2012. ...Of coarse it can be used by other brands as well
thingiverse
Scaled holder for table underside mount. ... 1.62 mm inner height, compatible with macbook pro retina 16. ...
thingiverse
This is a MacBook Pro 15 inch with Retina Display table holder. ...Dimensions, footprint: 140x30mm; height: 100mm; gap: 19mm
prusaprinters
Holder to stock your MacBook Pro. Print instructionsI printed this part with support and brim.
thingiverse
Stand for Macbook sized laptops such as the Macbook Pro or Air. Printed on a Flashforge Finder, with no supports or rafts. If you have problems, you can add supports to the overhang areas. ... When printed at 140mm wide, this fits a Macbook Pro or...
thingiverse
... Printed in about 7 hours using a .6mm nozzle. I also added a 14" model, although I don't have that size Macbook Pro so I cannot confirms it works as well until someone else prints one. ... Tips always appreciated at www.paypal.me/skylaapps
thingiverse
This is a clip that I hook onto my 2017 Macbook Pro that holds a wide angle lens I had purchased for my iPhone but never used. Now I can use this during my Google Hangouts meetings. It is pretty cool. ... Here is another one I noticed too: ...
prusaprinters
Printed in about 7 hours using a .6mm nozzle. I also added a 14" model, although I don't have that size Macbook Pro so I cannot confirms it works as well until someone else prints one. Tips always appreciated at www.paypal.me/skylaapps Print Settings...
thingiverse
I've made my own magsafe holder because the ones I've found were too big. The size is smaller then the other ones, thighter. I did have to make it fit better. The flexible part is a mixture between silicone and cornstarch (1:1) Mix this...
cults3d
Simple Cable holder/doc for the macbook pro retna machines. ...I remixed it to remove the usb section.
thingiverse
Simple Cable holder/doc for the macbook pro retna machines. ...I remixed it to remove the usb section.
thingiverse
exactly the same as Rymo's Cable management for a Macbook pro Retina. ...Exported in .stl
thingiverse
This holder is going great with [MacBook Pro Retina Connection Lock](https://www.thingiverse.com/thing:202491) for cables. This allow we to setup my workspace in matter of seconds. Remember to print it using with greater values of infill then...
prusaprinters
Then I though that perfect place to put my MacBook would be VESA 100 mount at back of my monitor. This solution not only solved my problem with space, only monitor was taking place on desktop, but also looks great. This holder is going great with...
thingiverse
This is a series of three prints that, when placed end-to-end are the width of the Macbook Pro and can hold the SSD case I bought. It also acts as a riser to raise the laptop up for easier typing and better airflow. I haven't been using htis...
thingiverse
Macbook pro retina & ipad mini holder Holder size: 12040100 Girder size: 66146
thingiverse
This Apple Macbook Pro USB C charger or AC Adapter holder or mount for the 96W for a standing desk. 3M foam double sided tape was used to adhere the mount to the bottom of the standing desk. Mesh file (*.stl) was modified using Autodesk Meshmixer...
thingiverse
Edit it online https://www.tinkercad.com/things/07lZ3ZlOZ0d I have created a MacBook Pro plastic case with a book and paper holder at the back. I am a person who likes to carry minimum stuff in the bag. I always wanted something attached to my laptop...