macbook pro stands 13 3d models
280064 3d models found related to macbook pro stands 13.prusaprinters
Hi, i designed a desktop stand for your MacBook, when using a monitor. fits MacBook Pro 13" 2016-2021, New MacBook Pro 14" -Settings recomendations:-Print with PLA/PETG, minimum 3 perimeters. -30% infill is fine-supports only needed...
thingiverse
**MacBook Pro 13" stand** ---- * A nice stand/raiser for your MacBook Pro 13". * Designed for the 2020 M1 version, but should also fit others (including MacBook Air). * You will need two to four M5 threaded rods and a few M5 nuts (+ optional...
cults3d
MacBook Pro 13" stand A nice stand/raiser for your MacBook Pro 13". Designed for the 2020 M1 version, but should also fit others (including MacBook Air). You will need two to four M5 threaded rods and a few M5 nuts (+ optional sticky rubber feet).
thingiverse
I designed this stand for my wife's MacBook Pro 13 2014 model with Retina display. I would recommend that you print it out this file if you have the same model described above, but, if you want to this model fit in some of the new models or even...
cults3d
Macbook pro unibody stand from 2008 to 2012. UPDATE: I made another version. It is for the same macbook model. In case you need the other one, it is still available. ... To further care for the Macbook it is recommended to use a plush or similar to...
thingiverse
Einfacher Halter zum Aufstellen eines MacBook Pro 13" von Ende 2011. Druck dauerte circa. 5,5 Stunden Erste Veröffentlichung von einer eigenen Konstruktion. Da ich noch Anfänger bin, besteht durchaus Verbesserungspotential. Die...
thingiverse
Slightly modified seongk's Macbook Pro Retina 15" Stand by reducing the height of the stands as well as the width of the overhangs. ...Trimmed the gap between the overhang to better fit the 13" MBP If you have a slippery desk, i suggest adding some...
thingiverse
My first 3D design work. ... It's for MacBook Pro 13.3 2017. Appreciate for your feedback. ... The stand angle is about 140 degrees
thingiverse
Press fit / clip together Macbook Pro 13 inch laptop stand Designed with tight tolerances, the legs slide in and clip to the top plate for a rigid stylish laptop stand.
thingiverse
Designed for the MacBook Pro 13-inch 2017 model (14mm depth), might fit other models.
thingiverse
Laptop stand, this was designed around 13" MacBook pro however it can be rescaled to fit whatever you need. ...I used 6mm wooden dowels for the middle bars however this is not necessary.
prusaprinters
Designed for the MacBook Pro 13-inch 2017 model (14mm depth), might fit other models. Category: Computer
thingiverse
After I printed it I realized that it is not suitable for Macbook Pro 13 inch. The laptops body was too thick to fit in. So I decided to create a version that fits Macbook Pro, is a little bit wider to add stability, and that uses less PLA. ... ...
thingiverse
The size is adjusted for the MacBook Pro 13. The two ledges on the lower sides are designed to do not protude out from the Mac shape and scratch your hands or arms, and the sides are smotted for this purpose. I printed it selecting 0.2mm layer...
thingiverse
Closed the gap in the original, made it thinner and adapted it to the macbook 13" with touchbar. ...Also added a small notch so it holds in the vent slots on the side of the macbook.
prusaprinters
Closed the gap in the original, made it thinner and adapted it to the macbook 13" with touchbar. ...Also added a small notch so it holds in the vent slots on the side of the macbook. Print Settings Printer: Print Rite DiY 3D Rafts: No Supports: No...
thingiverse
Laptop Stand for MacPro. ...Thickness of support is 8-12 mm Shell thickness 1.2 мм
thingiverse
Notebook stand e.g. ...for a 13" MacBook Air or Pro. Lifts the screen to an ergonomic height. Connect the side with a 8mm threaded rod. ... All can be printed in PLA 20% infill and no supports.
thingiverse
... looked for something to use with my Thunderbolt Display. ...I found some laptop stand which were not very stable. This is my version! This thing is suitable for 4 mm wide plywood or any other 4mm wood you can cut with laser cutter. ... Happy Lasering!
thingiverse
Small project while I learn to model in Fusion. Part of the challenge was to cut the model in pieces that fit the small bed of the Select Mini. ...Front legs are attached to the rear leg using a couple of M3 screws.
thingiverse
... lowest point. The shape of slot was designed to resemble MacBook's lower part profile for better fit and little gap. Tested with: MacBook Pro 13" M1 (2020) MacBook Pro 13" (2016) More photos: https://twitter.com/dr2mod/status/1546168022263537664
thingiverse
I wanted to store my macbook pro vertically while connected to my Akitio Node Pro. ... It requires a 3/8" Carriage Bolt. 8" seems to be perfect for the Akitio Node Pro and the Macbook Pro 13"
thingiverse
A stand for Macbook pro 2016/17. ... Tested with my 13" Macbook but a 15" Macbook should work as well.
thingiverse
For Apple Macbook pro retina 13" notebook stand Instructions
thingiverse
MacBook Pro 2018 13" Vertical Stand with open side for ventilation. ... Macbook Pro 2018 13" Halter mit seitlichen Lüftungsöffnungen.
prusaprinters
I didn't really want to change the angle that much, just get it off the surface so it wouldn't get so warm. I made it so it clips in on each side using the small recess the keyboard sits in, that keeps it tightly on the MacBook Pro so it doesn't...
thingiverse
I made it so it clips in on each side using the small recess the keyboard sits in, that keeps it tightly on the MacBook Pro so it doesn't slide around. I printed it out of PETG so it has a little flex when it pops on and off the sides. I printed...