mach3 3d printing

My old wooden LED bases are simple and elegant, but now I've created one that can be printed with ease. The distance between the LEDs is adjustable, controlled by turning the outer ring of the base. This allows for a customizable lighting experience...

You may also request this model printed and assembled with velcro at https://jkl-adapters.com/   **Description** To solve the tracking issues experienced by penholders while playing Eleven Table Tennis on the Oculus Quest 2, I created a series of...

The printed part sits flush with the trailing edge. I attached rudder horns I attach pushrods, there are some guide pieces for the tail pushrods. I installed the rest of the RC gear and adjusted the controls to my liking. I balanced the plane, my...

I have printed the lid in white PLA with slight indents for added light to come through at the right places. (it allows me to see the LEDs change so that I know it is working and not hung.) The lid is a (tight) push fit that stays in place well and...

youtu.be/LYm1B4P_h8A The two-layered planetary system of the "quick print" version was also only intended for calibration and demonstration. As you will find, the planet gears will twist under load and the clamping force will be quite limited. I've...

The keyboard's design is based off the Preonic layout.&nbsp;Printed on MK3S at 0.2 layer height and brim in Prusa PLA Silver. No supports, make sure to have the bottom correctly set on the build plate.</p><p>What you will need in addition to the list...

# Print Instructions: Be sure to use supports for the wall pin. I set this up so the gun points to the right to hide the screw holes. If you want to point it to the left, just mirror the gun holder and adapter plate. (I didn't test it, but I'm...

The whole size is the only change.3MF-  Two Colored: If you can print in multiple colors, use the 3mf files, which also use 6x2mm magnets.Printer SettingsLayer height - As low as you can go. I used 80 microns.Infill - It doesn't matter, I believe I...

Deprecated: Please use newer V2.&nbsp;This is my attempt to design a mount for the Bondtech LGX extruder with the LGX FF for flexibles hotend kit. The extruder is mounted sideways attached to a mounting plate via two M3 side screws into the extruder...

Post Processing: As I usually do with my prints, I remove the supports, then sand it down, after this I apply two coats of primer, sanding between coats. Once the model is smooth, I start painting the model using acrylic paints and DaVinci feather...

This set contains 5 heavily armoured Kingsguard Heavy Cavalry equipped with lances.  the Riders and Mounts are separate models for ease of printing and painting. Presupported files are included for each model in both STL format and LYS (Lychee...

For those who just want to print and don't want to do any soldering, I created a board with sliders that won't require electronics or additional work. However, it's not as awesome. Enjoy! P.S.: I didn't get around to painting it yet (ran out of...

Duplicate and mirror the mount and print the 2 mounts. 12/18 update: made a servo mount adapter that lets you move the servo back to the stock battery tray location. use the stock M3x8 screws. you'll need an M3 (3mm) threaded rod to extend the...

To make one, follow these steps: Select from the available options: * The back angle of your phone: 10 degrees * Whether to counter-sink screw holes in the center plate (screw count, depth and diameter are irrelevant): no * Wall thickness of your...

The one on the left in the picture above is not necessary, if you have already printed the original version is will still work fine. But the one on the right needed to be changed to clear to USB jumper/adapter/180 degree thing.  I chose to use the...

I had to print that after a craftsman tried to shorten the doors length in a rather barbarian style. The door is 83 cm in width - armed with an Ender 3 this translates to 4 parts with 205mm length each, leaving 1 cm uncovered as the door is so...

don't apply pressure on the pull. Cover about an inch every stroke, work your way along the blade. Keep the blade edge parallel to the sharpener edge. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 200...

**Gravitrax Ball wheel V2** - Difference in height 80mm - no support necessary - 3 pressure parts: wheel, gear, pillar - Printing time approx. 8 hours - it is required: (motor see links) 1 x M5 screw 50mm or threaded rod 1 x M5 washer 1 x M5...

Each side will hold a maximum of about 400 pages, making an up-to-800-page book when printed double-sided. I use this jig to bind both my PDFs and compilations of my children's artwork into neat archives for later enjoyment. We've probably compiled...

You’ll need to print the following and its best to fit in this order: If running the V6/Dragon carriage mod then fit the cable retainer and cable into it first, skip this step if you’re not. I’ve included a few options you could use: Cable...

Due to the adhesive discs on the wind turbines, a print bed with at least 210x210 mm is required. There are 5 different lids. With NabeTest you can adjust the bearing seat of the wind turbines with scaling in X and Y. The labyrinth ring is glued to...

Materials needed: You will need to print the 6 gear bearing: https://www.thingiverse.com/thing:53451 ** Thanks emmett ** 12v motor 12v variable resistor with dial 10' long speaker wire 10' long lamp cord female power plug 3' copper pipe brass...

To print this model, just remember a few things: there's no need for supports in any of the parts, and the printer should be accurate enough to handle shapes like the fan case and fan holder. When you assemble the fan case and fan holder, there will...

I have added another screw hole to it, but haven't printed or mounted it in that configuration yet, so hopefully the glue isn't required anymore. - Cap - to cap the bench mount suction when I am using the vacuum as dust collection for the other...

By making it modular, I am able to print extra parts to allow the structure to expand and in doing so carry more coins, as many coins as needed. For me with 6 pontoons and one cup, I was able to handle a maximum load of 1.2lbs of coins. In the end,...

Two are required, the shape is rotationally symmetrical so only one model is needed, and printed twice. The jig is 2RU (3-1/2") high which is the same as the smaller PDP-11/03 chassis height. To use, simply push the jig into the rack from the...

# Print Instructions: Be sure to use supports for the wall pin and the gun holder. Take care to clean the supports and leave a smooth finish on the gun holder. I set this up so the gun points to the right to hide the screw holes. If you want to...

This resulted in wasted project time as it was a 32 hour print. Therefore, I started thinking: could I turn this into some kind of jam sensor? The answer is yes, you can. So I set out on my mission to upgrade the Filament Bot. First let me say, my...

I would make the cable length to reach from your pants pocket to your goggles, or your shirt pocket, whichever works for you better. PS: If the LiPo buzzer is too loud stick two pieces of bubble gum into holes of little speakers, that will make the...

I think the rear is further apart, but you'll figure it out quickly when you try to attach to base.Use M6x35mm screws and M6 washer to attach top-cross bar assembly to the base!&nbsp;Other Remarks:Printed with Carbon Fiber PETG.Infill at 40%Used with...