macro ds 3d models

Create a new photo tray for DNP DS-RX1HS photo printerI broke the original and over $100 for a new, I decide to recreate and print my own version

This is a replacement focusing gear for a Meade DS-90 telescope. It will probably fit other meade telescopes too. ... Print this with the gear teeth up for strength.

Create a new photo tray for DNP DS-RX1HS photo printerI broke the original and over $100 for a new, I decide to recreate and print my own version

The Boss DS-1 is a renowned guitar effects pedal, delivering top-notch distortion sound to enhance your playing experience. ...This popular stompbox is a must-have for any guitarist seeking to add punch and presence to their tone.

Pen for Nintendo DS console\Printing in bright and fun PLA colors. I've found many useful designs and ideas on Thingiverse. ...Publishing my designs for free is my way of thanking the community.

Hi, this a LED-lid for the Synology DS-413, because you cant turn these of. Probably fits many Diskstations from Synology, and offers a dark room in the night. ... Happy printing!

I'm Looking for a Replacement Cover for My Weight Compartment in the Anker DS-2368, But It's Not Working Out. ...The Little Locking Tabs Need Some Supports to Make it Work Properly.

This tool enables you to utilize the Card Codes for Spectrobes on Nintendo DS. ...Simply browse through the code numbers at https://spectrobes.fandom.com/wiki/Card_Input and input them using my specially designed "All-Round Card".

Simply clutch alignment for Citroen DS / ID post 1965 manual transmission. It is for "3 fingers" pressure plate (see first photo), not for diaphragm one! ... It's only a tube...no particulary attentions for printing setting

Box to Store Nintendo DS cards. Use the customizer to set the number of Cards it can hold, 1 - 20. ... Inspired by: http://www.thingiverse.com/thing:44052 (was to big for my printrbot jr) Nintendo Copyright and stuff.

The metalic one does not realy suit the looks of the DS-12 so this printed in black will look much better and gives it a slightly higher tilt when set of a table.Two M5x10 will be required to complete the instllation. ...The holes in the printed part...

Introducing our 3D model of the DS-51/26 Armchair and DS-51/05 Footstool by de Sede, available at www.designconnected.com. Our collection features 6,500+ exclusive furnishings, including mid-century icons, contemporary classics, and designer...

# Hikvision DS-KH6320-WTE1 Mount This is a mount I created after acquiring several Hikvision DS-KH6320-WTE1 without their backing plates. The included design files are generated using FreeCAD. The screw holes in the middle are intended for use...

Nintendo DS/3DS Cartridge Holder - 20-Slot Capacity Conceived in response to a user's suggestion on my MicroSD Card design, this holder is specifically tailored to meet their needs: https://www.thingiverse.com/thing:3034162 Since I don't personally...

... it from the distance. Or just print it to make your childhood game look a bit more sophisticated and adult. NOTES: This 3D print is designed with the Nintendo DS lite (USG-001) in mind. ...The original Nintendo DS (NTR-001) won't fit in there.

Following this [Ifixit](https://es.ifixit.com/Gu%C3%ADa/Epson+WorkForce+DS-510+Color+Document+Scanner++-+clicking+sound+mulitple+page+feed+broken/65721) guide, I designed this replacement part. ...In the guide you can find the steps to replace the part,...

... to fit various formats and renderers. The DS-159 Sofa comes as a single editable mesh, with accurate dimensions in centimeters. ...Be sure to test their free 3D models before purchasing, and reach out to Design Connected's support for assistance.

This is cap for macro lens, use it with cell phones

This is a detailed specification for Academy's Macro UZI Airsoft Gun.

A simple protective cap for Nauticam N120 flat macro port, 67x0.75mm it thread.

For flash redirection for macro photography with the Godox TT685 Length: 250mm

The original IR macro lens ring just crumbled with the time. ...Print with TPU or FlexPLA.

Remixed DS hinge by HardlyHedgehog to accommodate the other side of the mechanism (replacement for hinge part connected to top screen). Simply use HardlyHedgehog's alignment hinge to drill into the top screen and glue in place. ...I used a little bit of...

Flat Case for DS and 3DS Cartridges. I wanted a design that mirrored rwindr's Switch Cartridge Case, so I basically followed his lead with some tweaks here and there. Instead of using the typical 4x2 layout, I decided to mix things up by...

The FreeCAD model includes an analogue instrument, specifically the AMS DS-UB130 (available at http://www.ams-messtechnik.de/). This device features both a voltmeter and an ampermeter. ...If the glass is not naturally transparent when importing, use...

Box for the charger Nintendo DS Lite is broken. When you want to print, make sure to set the Print Settings first. ...Printer: M3D Micro Rafts are necessary for a strong base: Yes The Supports feature is not available on this printer: No Resolution can...

... 64% of the original, which is just about right for 3.75" action figure displays. I used a brim, no supports and had no issues printing. Thanks to FigureWorks for the original files DS modular walls. ...https://www.thingiverse.com/thing:2772258

Mario's model ripped from Super Mario 64 DS. If you get any model errors when importing this into Cura, just ignore them. The model will print fine. ...I believe the reason why those errors show is because of the UV map inside of the model but I'm...

Spin this Nintendo DS card storage box with customizable settings! The customizer allows you to set the number of cards it can hold (1-20). Inspired by a Thingiverse design, print in PLA at 0.4 layer height with 0.4 infill. Secure games with a rubber...

Assembly instructions for the main elements of the DS 19 model in 1/6 scale. The elements reproduce the construction philosophy of this mythical car in a very similar way. Doors and hoods open. It is powered by a brushless motor of 2150KV.