magnetic ball and socket joint 3d models

Functional ball and socket joint attached to a foot for small robots.

Moves as a ball socket joint. The ball can be removed from the socket if you really tug on it. ...It is free moving, and has very little friction.

A ball and socket joint. Can be added to any assembly. ...This model is part of the tutorial series, tutorial coming soon!

More on this quick project over at: http://funbiestudios.com/2013/04/3d-printed-ball-and-socket-joints/ Support us on Patreon - https://www.patreon.com/FunbieStudios Instructions We printed this with glow in the dark filament with a Makerbot...

It's a ball and socket joint. Features: -Flat bottomed ball for easy printing -Unpatented Pronged Penta-Socket technology -Handy dandy cylindrical ball gripper Pro tip: the socket doubles as a decent head scratcher if printed large enough. Heck,...

The headphone clamp wasn't sitting flush with my desk, so I designed this ball and socket joint that contours to the curvature when the headphone holder bends. Installation: Screw this new screw about halfway in, then line up the socket on the top...

The headphone clamp wasn't sitting flush with my desk, so I designed this ball and socket joint that contours to the curvature when the headphone holder bends. Installation: Screw this new screw about halfway in, then line up the socket on the top of...

Joints for holding and providing relative motion between links

Make sure you snap it together while it's warm. ...Or stop it a few layers early. Other then that this is a simple ball joint!!

This Joint is a good solution for things like steering hubs and motor-sports. ...the threads are ISO M8 tapped.

This is a support-free joint that connects in series. ...Forms easily adjustable links and fun shapes.

... supports needed. Instructions Print 1 ball, 2 braces, and 2 rings. This thing needs no supports or rafts. Just have the printer print the ball on the stem and it should come out almost perfect. ... You will need a few screws to put it together.

A ball and socket joint with a locking ring. ...Configurable, and can be adapted to be used as an OpenSCAD library.

... joint for our project with 4 slots which allow for the movement up to 90 degrees+. ... More on this quick project over at: http://funbiestudios.com/2013/04/3d-printed-ball-and-socket-joints/ Support us on Patreon - https://www.patreon.com/FunbieStudios

This is a universial ball and socket joint. The grove around the edge of the socket is for an o-ring [ OD = 1-7/16" ID = 1-5/16" WALL 1/16" ] designed in order to keep the ball from coming out. This part is apart of a project for Humboldt State...

Add ball and socket parts Remix from https://www.thingiverse.com/thing:5216751 and https://www.thingiverse.com/thing:3268454

3D printable ball and socket design for use in many holding and arranging applications. this is a set of 6 individual pieces that print as 1 on a raft for easy layout. they are completely scalable. adapters and ends for various applications to...

There's currently a 20mm ball, threaded socket, and plain socket in this set. It's designed for 3mm or 4mm cap screw and #6 wood screw hardware. The plain socket is great for things that aren't very heavy like Raspberry Pi camera modules. It can...

This is a ball and socket joint designed to hold 4 neodymium magnets(3mm * 10mm), inspired by those magnetic car mount for phones you can buy on amazon/aliexpress https://goo.gl/5xJXiI. fully 3d printable. The flat end was intended to be mounted with...

You can also print my Polypanels Ball and Socket Joint Extensions to extend the reach and range of motion for your contraptions!  Also compatible with the Polypanels Triangle Ball and Socket, and Polypanels Nerf Dart Shooter specialty panels!  Oh...

Low cost Igubal 6mm rod end bearing with ball and socket joint For more information and dimensions see http://www.igus.co.uk/wpck/default.aspx?pagenr=2469&wt.mc_id=grabcad

Layers shouldn't split with this design since the lobes are vertical like on most ball joints. The one downside to this design is that hex screws no longer fit, and you have to use flat head screws. #6 and #8 should both work. ...Roughly equivalent to...

The head of the femur is the ball in the ball-and-socket joint of the hip. This model was made by Karina Riddell using Volumegraphics VGStudioMax 3.3 from a CT scan produced at the Yale Translational Research Imaging Center (Y-TRIC). The model was...

remix of the connections in the parent and a ball joint from Universal ball and socked arm thing 4193227. only partly successful, as the print needs to be strong. ... I think its me..

I designed a ball and socket joint inspired by https://www.thingiverse.com/thing:889439 to help me with a helping hands project I wanted to create. I took a different approach to the design and added dimple and detent system that allows for many...

... 6-10 minutes per bead, but this depends on how large you want it. Can make each bead a different color and add designs easily to make it your own. Link to blog: http://3dprinting.illustratingmath.com/2019/10/24/ball-and-socket-bracelet-necklace/

A nominal ball end can be tested with the sockets with an incremental fit tolerance. The numbers in the file names indicate the fit tolerance in millimeters. For example, 0-05_TOL indicates that the socket is 0.05 millimeters larger than the ball...

Neck Length - Distance between the ball and the socket (mm). Fluid Radius - Radius of the hollowed out section through the segment. Relief Slots - Number of slots in the socket - more slots = easier snapping together/apart. Can be removed altogether...

I designed a ball and socket joint inspired by https://www.thingiverse.com/thing:889439 to help me with a helping hands project I wanted to create. I took a different approach to the design and added dimple and detent system that allows for many...

Extension pieces for Polypanels Triangle Ball and Socket.  Take your articulation to new reaches! ... They are a little tricky to print, but do not require supports.  I slid the model down the z axis in my slicer about .4 mm to ensure a flat adhesion...