magnetic cable holder 3d models
439017 3d models found related to magnetic cable holder.thingiverse
A magnetic cable holder that fits 5x3mm round magnets. ...The cap is made for a cable that is 3mm in diameter (iPhone charger).
thingiverse
Parametric magnetic cable holder. Would work with PLA or other rigid materials, but the grip and flexibility of TPU are especially great for this. cable_holder_3m_3mm was made to hold the cable for a PineTime charger. All included models use 2 5x2mm...
thingiverse
Magnetic cable holder/Magnetischer Kabelhalter Simple. Guide cables along metallic surfaces. Cable(bundles) with outer diameter 8mm fit (slightly larger will also work). BOM: 1x countersunk screw M3x8 TX4 1x nut M3 1x pot magnet Ø16mm holding force...
thingiverse
Magnetic cable holder/Magnetischer Kabelhalter Simple. Guide cables along metallic surfaces. Cable(bundles) with outer diameter 8mm fit (slightly larger will also work). Parts list: 1x countersunk screw M3x8 TX4 1x nut M3 1x pot magnet Ø16mm holding...
thingiverse
cable holder can hold magnet. ... magmet size is diameter 6mm, height 3mm.
thingiverse
Simple cable holder - can be use with magnet, or simple washer if you put it mangetic strip.
thingiverse
This is a simple cable holder. It uses a 10mm diameter und 2mm thick magnet at the back. It can fit about 3mm cables. The hole for the magnet should be printed with supports for FDM printers. SLA printers should be fine without supports. ... I printed...
thingiverse
This is a cable holder with 2 magnets inside. The diameter of the magnets is 8mm with a hight of 1mm. You have to put one magnet inside the mount and glue it from the back to a surface. Then from the front you can see no magnet - only through the...
thingiverse
This is a simple cable holder with a slot for a magnet. It's very easy to attach the holder to the metal frame of your desk for example. A magnet from an old hard drive is perfect for this purpose. I stuck a small piece of non slip foam to the side...
prusaprinters
I made this cable clip/holder/organizer some years ago, which I shared on instructables before. It is great if you have steel shelf you can hang the cables easily. It also works for my power cord/usb cable of my laptop. My first print was with my Up...
thingiverse
... ... A micro USB end piece is permanently attached to both devices. In order to be able to charge one of the devices occasionally, I have fixed one of the cables with this holder on my desk. ... You'll need two neodym magnets of 8x3 mm and superglue.
thingiverse
Once the magnets are installed, just put a cable into the slot of the larger piece, and then snap the smaller piece onto the larger piece to secure the button to the cable. ... If you are careful with the polarity of the magnets (making sure each...
thingiverse
The model can be customized to any cable and magnet size. Magnets can be bought cheaply off [ebay](https://www.ebay.com/sch/i.html?&_nkw=disc+magnets), and I would recommend a 12mm diameter neodymium magnet. Smaller magnets may not fit with large...
prusaprinters
Quick fully parametric design to help you organise your cables.Customise magnet dimensions and the overall size. The magnet hole doesn't need supports, unless using quite a large magnet. ...I printed the arch with and without a small support in the...
prusaprinters
To build your own organizer use provided blocks (STL files) and combine them using PrusaSlicer (check provided 3mf files). Cable organizer can be mounted on the table or box using magnets, hot glue or double side tape. Magnet (20x6x2) can be inserted...
prusaprinters
Cheap DIY Logitech G PowerPlay alternative ;-) I've bought two usb cables from here: https://de.aliexpress.com/item/32830875598.html?spm=a2g0s.9042311.0.0.27424c4dBopr1j I use them to charge my wireless keyboard and mouse. A micro USB end piece is...
prusaprinters
<p>You need to split the stl-model into two halves in order to avoid supports. ...After printing you can put a super magnet of 15 mm diameter into the holder and glue both halves together.
thingiverse
# Yet Another Magnetic Cable Holder Just too lazy to look around Thingiverse. Let's reinvent the wheel again! It might fit to any 20 mm steel frame. However you can easily customize the model as it's written in OpenSCAD (in just 40 lines). ... ## BOM...
cults3d
**Elegant sleek magnetic cable organizer/cable holder. Holds cables up to 6mm in diameter to magnetic surfaces. Also makes a great toy/FidgetToy if you put two or more together, see photos. Download includes 180° version (cable holder) and 90°...
thingiverse
Magnetic Charger Cable Holder. ...Designed for a 8x3mm magnet, will fit snuggly without any glue.
cults3d
Magnetic Charger Cable Holder. ...Designed for a 8x3mm magnet, will fit snuggly without any glue.
thingiverse
Customized version of https://www.thingiverse.com/thing:2468779 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2468779
cults3d
Customized version of https://www.thingiverse.com/thing:2468779 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2468779
thingiverse
Customized version of https://www.thingiverse.com/thing:2468779 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2468779
thingiverse
Customized version of https://www.thingiverse.com/thing:2468779 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2468779