magnetic camera base 3d models

This is to adapt a Harbor Freight magnetic base to a 1/4-20 thread for mounting mics, cameras, and other things to it. ... Watch This Video to see what it's for https://youtu.be/oca56SyahMQ

I took the base if DanieBull's design and made it into a magnetic base mount for Wanhao and other printers with steel frames so the camera can be moved and rotated around at will. ...Post-Printing I made the divots on the back for 2 9.5mm x 1.5mm...

I took the base if DanieBull's design and made it into a magnetic base mount for Wanhao and other printers with steel frames so the camera can be moved and rotated around at will. Post-Printing I made the divots on the back for 2 9.5mm x 1.5mm...

I took the base if DanieBull's design and made it into a magnetic base mount for Wanhao and other printers with steel frames so the camera can be moved and rotated around at will. Post-Printing I made the divots on the back for 2 9.5mm x 1.5mm...

I wanted something that I could mount both the Ring Camera and Ring Solar Panel to that could be quickly moved to locations in a 7 acre industrial plant. It just so happens that there are many large steel structures that have at least 6 inches of...

As the CR-10S Pro (my printer) doesn't have the same rails for the Y-Axis, and is an all-in-one unit with a nicely sloping (30 degree) front to the steel enclosure that forms the base of the printer; I figured my best bet would be to do a remix of...

Magnetic Base

Simple Magnetic Base that a Dial Indicator may be attached to.

This is a remix of Funkatr0n's 30mm round base. ... I added a hole in the bottom for small magnet

3mm X 4mm Neodymium Magnets

Generic Mag Base for DTI

Brackets should be PETG, print them standing up with supports, not laying down for maximum strength The mobile camera housing uses a portable 12V power supply, there are many brands of the same one found on amazon and ebay

hola amigos, compre una camara, y les dejo el .stl de la base para tenerla cerca de su cama de impresión, la adapte para la estructura de una ender 3, pero dejo el archivo para SolidWork y puedan editarlo, los he impreso con las siguientes...

I had a spare Microsoft camera laying around with a magnetic base. Rough mock-up with a slot to allow adjustability of the magnet (current diameter is ~10.15mm). Tight fit on the front x-axis frame. Haven't checked clearance beyond an eyeball test,...

So i quickly went into Fusion 360 and wipped up a magnetic base for the same camera housing. The magnetic mount uses 3x8mm Neodymium disk magnets that I purcased of ali express, and makes the mount sit secure without beeing stuck so hard that you...

Print Settings Printer Brand: Wanhao Printer: Wanhao Duplicator i3 V2 Rafts: Doesn't Matter Supports: No Resolution: .2 Infill: 50% Notes: This will require a brim since the ball on the camera mount as very little touching the bed. The Camera mount...

This uses a 1/2" x 3/8" rare earth magnet (picked up from CMS Magnetics on eBay for another project) to clamp the camera to the printer housing. Remove the camera from the bulky plastic housing, and reuse two of the screws to attach the board to...

... Thumbscrew for Heatbed M3</a>, which uses a brass insert. <hr> <strong>Like my work? Post a make! Update 6/30/2021 Created shorter versions (v2) with 5 magnet holes (3 on top, 2 on side) for base and rotated properly for printing. ... <hr>

A magnetic base/stand

Although this is designed to work with my Logitech C270, you should be able to mount nearly any camera to this mount. You'll need some M3 hardware and four 8 x 3 mm magnets. (Mine measured 2.67 mm thick.) First make sure your magnets will fit, then...

The "connection" is not strong enouth to hold my camera vetically (I sould have used stronger magnets). I also uses a bolt and a nut for the top and bottom pieces to attcj to tha camera and tripod. You have to be careful to ensure all the magnets...

I used three of these magnets and one of these arms to make a magnetic camera arm. This will come in handy when I'm making youtube videos. ...

magnetic indicator base improvements magnetic base dial indicator magnetic base dial indicator repair repair magnetic base Video link https://youtu.be/RUV55lXNBaY

Replacement plate for cheap magnetic base

Requires 3 cylinder magnets 8mm dia, such as http://www.robotdigg.com/product/55/Cylinder+Magnet and a short 1/4" or M6 screw Designed for Wanhao Duplicator i3 + Logitech C920

This is by request. ...Its a the magnet base holder for a magnetic bearing system

Small base to cover the 2x2 magnetic base made by devonjones

Magnetic Base for Tripod 1/4"-20 Flange Nut 32mm x 8mm Neodymium Magnet Phone case on the image: https://www.thingiverse.com/thing:3237560

This is a simple magnetic base with a removable top plate. The knob adjusts the position of the magnet carrier which turns the strength of the magnet's holding power up or down. Total strength will depend on the class of magnets and thickness and...

... store. Set contains bases in these sizes: - 25mm round w/ 6x3mm magnet hole - 28mm round w/ 6x3mm magnet hole - 32mm round w/ 6x3mm magnet hole - 40mm round w/ 12x2mm magnet hole - 50mm round w/ 12x2mm magnet hole - 65mm round w/ 12x2mm magnet hole