magnetic catch push to open 3d models

I had a magnetic catch bowl for holding screws, and I wanted to mount it to the printer, so I designed this little platform that takes a big washer that I got at Home Depot for less than 50 cents. ... Washer Outer Diameter: 50mm Washer Inner...

Magnetic door catch designed to be mounted with double adhesive tape (3M or similar) on the floor and on the door, no nails or screws required. Door piece can also be glued on for more resistance to pulling. Requires 4 button magnets of 10mm...

  Inserting a couple of small (10mm x 2mm or 1.5mm) magnets into the parts will not only prevent that, but will provide a satisfying click to confirm all is in place. Inserting the Magnets (this is harder to describe than it is to do!!)The magnets...

This is a spacer I made for the OCGIG 5 PCS Push Button Latch Cabinet Door Catch Keyless Cupboard Locks for RV Yachts Motorhome Camper Caravan on Amazon to work with half inch boards.

... when the top is removed. Larger handles were also incorporated into the center of each door, making it unnecessary to keep the "knob" part of the door side magnet intact. ...To facilitate easy editing, I included *.step files for both designs.

... in millimeters and accurately scaled for use as-is. Available File Formats Include: Rhino 3DM (native) OBJ FBX STL 3DS Note that since this design uses NURBS curves and not mesh retopology, some limitations apply to non-Native file formats.

Home Depot's Everbilt PN: 1002 782 609 is a premium white economic magnetic latch featuring a sturdy strike plate.

The catch tray features a magnet at its top, which securely attaches to the magnet at the planter's bottom. A total of 5 magnets are situated on the back of the planter and 2 on the rear of the catch tray, effectively holding them in place against...

These push button cartridges are compatible with the basic "Modular Candy Dispenser" found here: https://www.thingiverse.com/thing:4606016 These open cartridges allow you to see the spring mechanism in action and see what color candy is coming next.

Print Settings: Printer Brand: Prusa Printer: Prusa Clone Rafts: Doesn't Matter Supports: No Notes: To get the best results, print this design standing up with a brim. ...I used 100% infill for my print, but it's likely not necessary - a 50% infill...

I quickly crafted a base for Open Forge tiles to accommodate the 100pcs of D2 x 1mm N40 Neodymium magnets I purchased, and I'm sharing it with you. ...The magnets themselves can be found on Banggood at...

These extensions are designed to snap onto the baseplate of your benchtable and can be secured using one of the screws provided. ...If you run into any issues or have a brilliant idea for another extension, feel free to share your thoughts in the...

... ... All expansions are intended to be mounted onto the baseplate of the benchtable, with the option to secure them using one of the provided screws. ... If any issues arise or you have an idea for another expansion, feel free to leave a comment.

To change between options, modify the line "magnet_hole = true;" in the .Scad file to either "magnet_hole = false;". This project aims to reduce research costs by providing low-cost scientific optical hardware. ...More information is available at...

The optics base comes in two versions: a flat one for use on a standard table and another with a small cylinder at the bottom designed to hold a magnet, ensuring components stay in place on magnetic surfaces. To remove or add the magnet hole from...

Feel free to leave me feedback in the comments and let me see your prints ___________________________________________________________________ Design: The Logo is taken from the official open source hardware association Homepage (Link below). I just...

There are two Neodymium Magnets in each of both parts, so you can easily connect both parts through a shirt, no needles that possible leave marks on high quality (button) shirts.This could be actually used for any type of pin, flags, company logos,...

A small display pedestal for your 5-way Push-to-Connect manifold system.

hi best push pull by Five_Seven  Rally Magnetic Push-Pull Paddle Shifter https://www.thingiverse.com/th... rally push pull for plate t500 - tspc -for t300? the center replacement : https://www.thingiverse.com/th... i remak the place of magnet : 50...

This is a group of remover tools for push-to-fit plumbing fittings. ...(e.g., Sharkbite). They have a bevel and a wide finger grip to assist in removing push-to-fit fittings—one for each size of 1", ¾", ½" pipe.

A flexible hook to hold a ball jar under bottle opener to catch bottlecaps. Jar can be pushed in to place and pulled out easily with one hand, stays securely in place. No more bottlecaps all over the floor. ...I installed so that the top of jar is about...

I'm testing out a new model and I've opted to use the Wyloch 1.25 size, which offers superior magnet placement compared to my previous attempt. ...For this build, I'll be utilizing 5mm ball magnets for added stability and precision.

This is a working version of push-pull paddle using mini micro-switch and smalls magnets (6mmx2mm). Since I couldn't find any free mechanism of this kind anywhere, I decided to create it. The main body has two holes for grub screws to restrict the...

To maximize its strength, I employed 5x8mm neodimium magnets, but you're free to experiment with whatever suits your needs best. The result is a beautifully self-centering terminal, a testament to excellent design! This innovative concept should...

Many of us are forced to work out at home right now and this is a great item to add more functionality to your dumbbells. They use the standard 1" Spinlock thread but I also included a non threaded version that will fit any 1" bar. It also...

This are some Push-Pull paddle shifters with The holes to attach this shifters to your wheel are for M4 screws and are 12.875mm apart. There are two versions of these paddles. One with the magnets contacting each other and another separated 0.8mm.

The 11x2.5 hole is big enough for a lot of magnets.The magnet can be smaller than the hole.Don't forget to pause the prints.And observe the polarity of the magnets. ...It must be inserted in reverse into one of the models. I used the classic empty...

A model that allows you to use coconut wafers to grow your plants with "ready to grow" lighting, quite simply!

A sleek device designed to activate an elevator button with minimal contact, perfect for those who prefer not to touch public surfaces directly. Conceived in response to concerns about hygiene and germs on frequently touched buttons. ...Made to fit...

The digital files cannot be used to manufacture these parts-some details have been removed. But you can use them to design your parts. ... Video: https://youtu.be/I6BGY7CRHH4 More: https://www.tanerxun.com/