magnetic hex bits 3d models

A Hex bit holder with magnets inside to firmly hold them. ... They are oriented in a way to make them easy to grab with 2 fingers.

This is a magnetic hex bit holder. You will need 5 8mm diameter x 2mm thick neodymium magnets. ... Also you will need to pause your print at approximately 3.1mm to insert the magnets.

This is a magnetic hex bit holder. You will need 5 8mm diameter x 2mm thick neodymium magnets. ...Also you will need to pause your print at approximately 3.1mm to insert the magnets. Print instructionsCategory: Tool Holders & Boxes

magnet hex bit holder need 3 Peaces 20*10*2 neogym magnet

Small and grippy Hex Bit driver with room for a magnet. (3x8mm) Just pause if you want to insert a magnet to hold the bit in place. ...

At work I have to carry around a bunch of different hex bits all the time, so I designed a little holder for my pocket. It holds 4x 1/4" standard bits and one 5/16" bit (Torx50) and has a little hole for a leash. During the print you have to insert...

20 slots bits are held by magnets hole to apply a key ring (and carabiner) Payload 4 x 2mm magnets. ... #3x15 Round Head screws Add-on

The tool accepts any 1/4" hex bit, and there is room for a small magnet inside each part -- insert the magnet in the same hole where the hex bit would go. Use superglue to attach the magnet to the bottom of the inside of the part. You'll need to...

I made this hex bit holder to check my calibration in the X & Y directions. It is made for an 8mm diameter x 3mm magnet (which I bought at Home Depot). ...This can be used with my "Magnetic J-head mount / retainer" found here:...

hex bit holder for manual use of step dril

hex bit holder for manual use of step dril

A modification of another hex bit holder here. I wanted magnets that didn't need to be glued in, AND I didn't want the bottoms of the magnets exposed to pick up all the metal filings in the shop. By using 8mm magnets and adding a bottom cover that...

... are 1cm deep, so this is intended for full size bits (e.g. meant to be inserted and held in an impact driver on their own). So it may not be ideal for smaller bits. I'll consider making a shorter version for the simple stubby collar-less hex bits.

Customized version of https://www.thingiverse.com/thing:3195998 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3195998

A simple box for hex screw bit storage, in a honeycomb style. Magnetic attachment to metal. ...magnet: 10x2 mm Print Settings Rafts: No Supports: No Resolution: 0.2 Infill: 10%

This is a magnetic base to add to V1 of the [Ridgid Hex Bit Mount](https://www.thingiverse.com/thing:4348587), because bits fit too loosely in the V1 design for me. It's functional but I'd prefer if I had used bigger magnets or a non-magnetic...

You have to print the original “hex bit handle” and this thingy. Use print instructions from there for both parts.I printed both in prusa orange PETG.After printing superglue a neodym magnet (6mm diameter, min. 2mm thick) onto the shaft. Then put the...

Loose hole so that the bit can easily slip in, and a small magnet on the bottom to hold them even if you hang them upside down The magnet is a cheap 3x3 cylindrical neodmium magnet that you can press fit with a pair of pliers, and the two parts are...

9mm Magnet Adapter

I am printing a number of these to have as an extra in every bit set around the house. I am printing the main body at 50% for strength, probably overkill, but hey. I am printing out the top separately at 30%. ... To assemble, place magnet in recess,...

hex bit holder designed to go over a 3/4" wide magnetic small parts rail. There are 2 holes in the side that are a tap drill size for 8-32. The picture shows 3 holders next to each other. Each holder is 7.5" long. ... 25" Magnetic Small Parts Rail:...

U'll need 2 magnet discs D8xh4 mm https://youtu.be/kdD4kAjN1fY enjoy

Very small hex bit driver with ~27 mm diameter and 25,4 mm height. With room for a Ø10x2 mm magnet. ... Update 2018-08-27: added Fusion360-file

Customizable hex bit holder with a separate slot for a magnet at the bottom. You can specify the sizes and depths of everything, including the magnet size. For the magnets, I used 6x3mm magnets. Put a dab of glue in the magnet hole and force in with...

Changed from my previous version and now using four 8x3mm magnets, one placed at the bottom (layer 1) and under each hex pocket so that the magnets will hold the bits in the rack and also secure the rack on a metal surface. At layer 13 you will be...

Only changes are I added two embedded 10x2mm magnets into the base and chamfered the bit openings slightly. About 19 minutes into the print job (if you use my .3mf file) is a pause for inserting the two 10 x 2 mm magnets. If you find the magnet...

I decided to rather model and print this "wrench" holder to act as a lever and holder for the hex bit in order to do what one does to screws. Since I had no handy dandy magnets lazing about, I went for the snug fit approach and yes, it's a snug...

Instructions You need: 3 x printed part n x magnets d=8 h=1 (n - number of bits on one side) 2 x M3x20 screws 2 x M3 nuts The 8mm megnets still available at DX.COM: Super-Strong Rare-Earth RE Magnets (8mm 20-Pack) Building instructions: Place the...

... previous attempt](https://www.thingiverse.com/thing:4441645) and work from [Fjederhaek](https://www.thingiverse.com/thing:4399253). ... ### Parts - 8x 5x2mm round magnets - 1x 4mm magnetic screw bit extender 100~150mm total length (short is better)

Customized version of https://www.thingiverse.com/thing:1463357 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1463357