magnetic iphone mount 3d models
424170 3d models found related to magnetic iphone mount.thingiverse
Cradle modified to allow the addition of the metal backplate for use with the Koomus Car Mount. ... Adjusted width from 80mm to 79mm and it fits perfect with a Spigen Ultra Hybrid ...
thingiverse
This is a modular mount for your car to mount anything you want using magnets. The mount stays in the CD player and then you can created any module you want to attached to that. The two mounts I've made here are for the iPhone X in Portrait and the...
thingiverse
This is a magnetic mount for use with any smartphone but utilising a magnetic stick on base for the back of the phone (or case). I use a ram mount suction cup mount for the windscreen. I use neodymium magnets superglued to the back of the round...
thingiverse
i designed this to mount the Hoidokly Magnetic Charger for iPhone to an Brodit Base.
thingiverse
8bitdo lite controller mount for iPhone 12 using magsafe magnets. The controller holder is designed to fit 8bitdo lite, it fits it nicely and it can be charged without removing the holder. There is a slot at the end to show the 4 LED lights at...
thingiverse
This phone holder allows you to use you iPhone SE (Gen 2 or 3), iPhone 8 or iPhone 7 with a magnetic phone holder. Normally, you would just stick a metal plate to the back of the phone for the magnet to attract. However, attaching a metal plate to...
thingiverse
Magnetic car-mount holder for Iphone 12 Pro with original silicone case. ...2 versions (slightly different) https://youtu.be/LKanFU1O-h4
thingiverse
This device is a modified iPhone 5s case with a mount for https://www.thingiverse.com/thing:2448971
thingiverse
Simple iPhone 6S stand with magnets Need 4 square magnets 10x10x10 mm Supportles design. Easy to print Простой держатель для телефона. Подходит на iPhone 6S. Дополнительно удерживается магнитами. Для сборки потребуются 4 неодимовых магнита...
cults3d
This is a simple dock I created to hold an iPhone 6 without a case to a magnetic surface like a refrigerator, magnetic bedroom wall, file cabinet, whatever. ... You'll need a: - standard lightning cable - short m3 set screw - 0.5" diameter x1/8" thick...
thingiverse
This is a simple dock I created to hold an iPhone 6 without a case to a magnetic surface like a refrigerator, magnetic bedroom wall, file cabinet, whatever. ... You'll need a: - standard lightning cable - short m3 set screw - 0.5" diameter x1/8" thick...
prusaprinters
<p>Keeps the doors of your furnitures closed. ...Requires 2 magnets with 5mm radius and two screws that are magnetic
youmagine
Magnetic mount to hold cabinet doors, faceplates, covers in placeHoles are designed for 6x3mm Neodym magnets.
grabcad
Designed this case to be either 3D printed or cut on a CNC. ... Link to the magnets are posted below. ...http://www.gobrushless.com/shop/index.php?app=ccp0&ns=prodshow&ref=M10-4-2
thingiverse
This dock requires two magnets 10mm in diameter. These fit into the recesses on the bottom of the dock to stop it tipping over. Lightning connector fits in from bottom but would need gluing in place. ...(I used blue tack so I could remove it...
thingiverse
Magnetic mount to hold cabinet doors, faceplates, covers in place. Holes are designed for 6x3mm Neodym magnets. ...Print Settings Rafts: No Supports: No Resolution: 0,2mm Infill: 30% Post-Printing Bill of materials 2x Neodym magnets (6x3mm) Superglue
thingiverse
Magnetic mount is for hanging pistol on a metal wall in safe without drilling. You need 3 neodymium magnets 10mm in diameter and 3mm thick. ...Just stick the magnets into the right place with hot glue gun and you're done.
thingiverse
I used this to mount my brush on my table's steel leg as its a little high for http://www.thingiverse.com/thing:968344 Holds a 20 or 22mm, 2.5mm high neodymium magnet. Fasten with 2 M3 screws. Additional mount included for this cheap IKEA brush, if...
thingiverse
iPhone 11 Pro case with cutout for the Cigar Magnetic car mount backplate magnet. ... Also USB cutout is sized for one of the circular magnetic USB chargers since I use those when not charging in the car.
thingiverse
iPhone 6 holder for the fridge. ... The width and thickness are oversized for phone with case. Print vertically. The slot for magnet will accept a strong hard drive magnet 4x20x40mm. ... You will need a very strong magnet.
thingiverse
This part enables me to place my iPhone, encased in an Otterbox case, on my leg while I drive. A magnetic charging disk couples to the phone. The assembly is bolted to a beanbag so it doesn't slide around. I only use my phone to record my voice,...
prusaprinters
The slot for magnet will accept a strong hard drive magnet 4x20x40mm. ...You will need a very strong magnet. Print Settings Printer Brand: Prusa Printer: i3 MK3Rafts: No Supports: NoResolution: 0.3mm Infill: 20% Triangle Filament: [...
thingiverse
Mount for mobile phone, avoiding visible screw holes. ...Works with Iphone 5, 6
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=1655546 Instructions Using the following options: support = 1 phone_depth = 4 phone_width = 66 extraD = 0 offset = 0 font_size = 11 connector_height = 15.7 phone_name = iPhone 5S connector_depth...
thingiverse
remix of https://www.thingiverse.com/thing:4164350 Split in 2 halves for attaching a gooseneck...
thingiverse
phone mount specified for iphone 4s in a gorilla/survivor case and possibly other models??? ... may need to file down the tactical rail bars to fit.
thingiverse
I wanted a mount for my iphone in its case with that would allow me to rotate the phone around the axis of the camera. In the iphone, the camera is offset, so I added a mount there for the tripod. In addition, I wanted the frame to pivot horizontally...
thingiverse
So, if you want a mount that fits on your bed rail, and can wireless charge your phone, try this. The rail size is 3/4" and this should fit pretty snug, depending on how tight you have your settings dialed in. It could also be improved, so if...
thingiverse
Magnetic Gopro Mount Add pause in slicer during print to insert the magnets (disk 15x3mm) 4 Loops to attach a cable tie No support material needed Edit:...