magnetic socket holder harbor freight 3d models
411884 3d models found related to magnetic socket holder harbor freight.thingiverse
Replacement slide on 3/8 drive socket holder insert for the Harbor Freight magnet organizer. ...Friction fit rather than ball bearing snap but it works fine.
thingiverse
This is a bit holder for the Harbor Freight socket hex bit 9 piece set. ...Very handy for my workbench .
thingiverse
Tool holder for 9 piece 3/8" & 1/2" drive hex socket set from Harbor Freight. Fits this product: https://www.harborfreight.com/9-piece-38-and-12-drive-metric-hex-bit-socket-set-67880.html Counter bored holes in the bottom are for 3/8" X 1/8" magnets...
thingiverse
This creates a nice socket holder for Harbor Freight Pittsburgh Pro metric sockets. ...Each socket is recessed into the holder so they do not fall out.
thingiverse
This creates a nice socket holder for Harbor Freight Pittsburgh Pro SAE sockets. ...Each socket is recessed into the holder so they do not fall out.
thingiverse
This is a holder for the 3/8 Allen sockets sold at Harbor Freight. It has 6 slots for 4, 5, 6, 7, 8 and 10mm sockets and the option to add a 12x3mm magnet at the bottom for additional securement. ...I have found that I didn't need the magnet, as it's a...
prusaprinters
... and one with an open bottom (shell). ...I like the shell, printed face down. Made for Harbor Freight Pittsburgh Wobble Socket Extension Set. ...I taped off the top and then spray painted the inside yellow to easily see when a piece is missing.</p>
thingiverse
Simple holder for HF 67011 Square drive socket caps. It keeps them from rattling around in your toolbox and I haven't seen a good way to keep them together. I made two versions - one that uses the HF rare earth magnets and one that just has holes...
thingiverse
... a great deal ($5 on sale regularly). ... Both SAE and Metric bits have 2 3/8" and the rest are 1/4". https://www.harborfreight.com/40-pc-38-in-14-in-drive-sae-metric-socket-set-62843.html Plan to add a socket holder for the 3 8 points and the adapter.
thingiverse
I picked up a magnetic tool bar from Harbor Freight [(item # 60433)](https://www.harborfreight.com/18-in-magnetic-tool-holder-60433.html) and was disappointed that the mounting holes were not 16" on center so I could mount it securely to my wall...
prusaprinters
I picked up a magnetic tool bar from Harbor Freight (item # 60433) and was disappointed that the mounting holes were not 16" on center so I could mount it securely to my wall studs. Sure, I could use wall anchors, but what fun is that when you have a...
cults3d
I picked up a magnetic tool bar from Harbor Freight (item # 60433) and was disappointed that the mounting holes were not 16" on center so I could mount it securely to my wall studs. Sure, I could use wall anchors, but what fun is that when you have a...
thingiverse
Deep/ Shallow impact socket holder for harbor freight impact sockets along with a 15mm added. ... Wobble sockets holder as well
cults3d
Deep/ Shallow impact socket holder for harbor freight impact sockets along with a 15mm added. ...Wobble sockets holder as well
thingiverse
Quick socket organizers I made for harbor freight deep well socket sets. I've included a file for both SAE and metric sets. ...
cults3d
Quick socket organizers I made for harbor freight deep well socket sets. ...I've included a file for both SAE and metric sets.
thingiverse
3/8 SAE fits Quinn - https://www.harborfreight.com/hand-tools/sockets-ratchets/38-in-drive-sae-chrome-deep-socket-set-10-piece-64215.html 1/2 SAE fits Pittsburgh Pro -...
thingiverse
I love the 18in Harbor Freight Magnetic Tool Holders. I have several in my garage and office. I recently dropped a big thing of small screws and nuts and most magnetic sweepers are way too expensive for me for occasional use. Harbor Freight has a...
thingiverse
4x5 Magnetic Holder for the very common 40pc SAE/Metric Socket set by Pittsburgh from Harbor Freight. Printed with raised lettering to identify socket sizes, these can simply be marked with a sharpie to have them stand out. ...Build is roughly 250g.
prusaprinters
Holder for Harbor Freight Universal Impact Joint Socket Adapter Set. ...I recommend printing face down; should work without support.</p>
thingiverse
This is a magnetic bit holder for a Harbor Freight Bauer 20V drill or driver. It uses two 8x2mm round magnets that you must glue in. ...The holder has two 15mm deep hex slots for shorter bits and can hold a long bit or drill bit on the outside.
thingiverse
I designed this socket organizer specifically for the impact socket set from Harbor Freight as shown in the picture. I found that removing sockets from the holder they come in is not very convenient and as you can see easy to break. I engraved the...
prusaprinters
<p>Fusion 360 model included. ...This was made to hold a Harbor Freight socket adapter set. I recommend printing it face down.
thingiverse
Printed in PETG+, I remixed the original design from user Samhyamss to accommodate the slightly larger dimensions of the Magnetic Tool Holder from Harbor Freight. ...Fit is snug and filament should just barely stretch to fit the clips into the Skadis...
thingiverse
This is an organizer for the Harbor Freight socket set SKU 62843, 47902, 61328, 63015, 975. Currently, these cost $6 at my local HF. I'm satisfied with my socket set, but the thin plastic organizer/divider is horrible quality. This will cost...
cults3d
This is an organizer for the Harbor Freight socket set SKU 62843, 47902, 61328, 63015, 975. Currently, these cost $6 at my local HF. I'm satisfied with my socket set, but the thin plastic organizer/divider is horrible quality. This will cost about...
thingiverse
A stand for a Harbor Freight Multimeter. ... I added some pockets for magnets to the stand.
myminifactory
I designed this Harbor Freight flashlight holder so when I change tools on my machine at work, I can see in the dark tight areas. This holder uses 5mm x 5mm x 3mm thick magnets. ... I have also included the Fusion 360 file so anyone can change it...
thingiverse
I designed this Harbor Freight flashlight holder so when I change tools on my machine at work, I can see in the dark tight areas. This holder uses 5mm x 5mm x 3mm thick magnets. ... I have also included the Fusion 360 file so anyone can change it...
thingiverse
a basic screwdriver holder to hold the cheap @$$ blue multi-screwdriver from the good ol harbor freight. printed with the flat side down. designed to be affixed with a 3m command strip. ... harbor freight screwdrivers like this have really poor...