magnetic tube 3d models
123913 3d models found related to magnetic tube.pinshape
This is a Magnetic Tube Holder for a Backpack. Designed with CamelBak's in mind, this handy, life-hack device clips on to your backpack's strap and water tube. I like to call it the CamelHack :) Check out my website, https://www.mattiatbutera.comfor...
thingiverse
My magnets were from K & J magnetics, 17 cents each (1/8 x 1/8 x 1/4 inches) How I Designed This I looked up the camelbak magnetic tube clamp in Google images, then just modeled it by eye. ...I used a caliper to take some measurements, like for the tube...
thingiverse
a magnetic tube rack designed to fit 15 mL eppendorf tubes. $800 is too much to spend on a tube rack, so I decided to make my own. ...Magnets, PLA, and all will cost < $100 total.
thingiverse
Larger magnets: http://www.kjmagnetics.com/proddetail.asp?prod=BC42 These are jammed in side by side with the smaller magnet to make a continuous 1-1/4" magnet for the PCR tube rack. Jam it in so the poles line up. Yes they will want to spring out...
prusaprinters
I managed to snap off the clip from the original tube clip I bought even before I got it out of the cardboard packaging!You can “peel” off the remaining plastics around the magnet (with side cutters) and then place the magnet inside this printed...
thingiverse
"Remix" of the magnetic tube rack, with one fixed STL. To fix the STL, run it through Microsoft's 3D builder (sorry Mac owners :( ), and it should prompt to fix it. I tried to fix all three given STLs, but could only get the four tube one (the others...
thingiverse
This 0.2 mL magnetic tube rack is useful for DNA/RNA separation using paramagnetic beads (e.g. SPRI). The 8-well slot can hold tubes in both a high and low bead pelleting orientation (top and bottom), useful for washing pellets or pulling off...
thingiverse
Magnetic holder to attache a drinking bladder tube to a Evoc backpack easily. ... I used 20x6x2 mm Magnets.
thingiverse
This model is built to hold a 3/8th OD silicone tube to the wall by gluing 14mm (or under) magnet into the holes of each model. This lets me use my waterline and then secure it quickly to keep it from getting dirty. The holder is 16mm wide, 16mm...
thingiverse
... hole in the back is for a 3x8mm neodymium magnet. the tube should have a tight fit in the hook and the whole clip can be attached to any pice of clothing via a second magnet Diameter - French catheter scale 3mm - 9 3.3mm - 10 3.6mm - 11 4mm - 12
thingiverse
This is the cheap alternative to buying the original magnetic bead tube holder. (1/1000 of the price). For this model you will need a round magnet with 16 mm diameter. Or you use the step file and change the slot for the magnet yourself, eventually...
grabcad
... isolation rack. ...It holds eight 1.5ml tubes. This rack avoids gluing the magnets in: two 10mm x 3mm x60mm bar magnets, available on Amazon, slide into the sides. ...The top is a snug fit for our 1.5ml tubes but they come out without much resistance.
thingiverse
... ...This holds 8 1.5ml tubes and uses 10mm x 3mm x 60mm magnetics to isolate the magnetic beads in solution. ...It also avoids the glue needed for other designs and has an 11mm opening which is more forgiving than other designs (your mileage may vary).
thingiverse
To be updated To lead the PTFE tubes to its respective spools and using FILLER spool holders a flexible attachment to the Skadis peg board is needed that also allows for some distance to the walls. Hence, I quickly merged two designs that I am trying...
thingiverse
Remixed 0.2 mL magnetic tube rack for DNA/RNA separation using paramagnetic beads (e.g. AMPure mag beads). The original rack is designed for 1/4" diameter x 1/4" long rare earth magnets. This version is meant to fit two racks back-to-back, with each...
thingiverse
This means you can easily reclaim the magnets, you don't have to worry about anything smashing into and chipping the magnets, you can use any length (or even round disk) 10×3 mm magnets, you are less likely to have rusting from water exposure, you...
prusaprinters
Easily push your filament to your printer.Requires 15 5x5mm magnets2 Wood Screws10 PC4-M10 Male Straight Pneumatic PTFE Tube Push in Quick Fitting Connector
thingiverse
Magnets used: https://amzn.to/3ImOxqn Test Tubes Used: https://amzn.to/3OqG2ON Want them to grow fast? Get some of this: https://amzn.to/3ofs7An Was this model helpful for you? Consider supporting my work in any of the following ways! Even the...
prusaprinters
For use with magnetic bead for peptide purification. No supports required to print, if printed where the rack is on it's side. Requires sixteen 12x2 mm neodymium magnetic disc. Category: Biology
thingiverse
For use with magnetic bead for peptide purification. ... No supports required to print, if printed where the rack is on it's side. Requires sixteen 12x2 mm neodymium magnetic disc.
thingiverse
A stand for 1.5 ml Eppendorf tubes with integrated magnets. Suitable for SPRI-beads like Ampure XP for DNA clean-up. Requires 20x10x3 mm neodym magnets. Actual measurements of the magnets I used were actually slightly smaller than that...
thingiverse
Tube rack with a metal plate measuring 160x41x2 or 80x41x2 . I bought in the nearest hardware store. ...It allows you to mount the magnets of any size, as it will be convenient.
thingiverse
A system for different sizes of test tubes which can be stuck together by magnets. The magnets can be pressed in from the sides of every stands. The magnets should habe the size of 5x5x5 mm. Not for commerical use. The models should only be used...
thingiverse
They fit in an angled position so that the distance of the bottom half of the tube to the magnet is minimized, for a further increase in performance. ... You will also need: - 8 neodymium magnets, 2 cm x 1 cm x 0.5 cm; - 2 screws (this design was tested...
thingiverse
Customized version of https://www.thingiverse.com/thing:6175814 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=6175814
thingiverse
Show off the power of magnets with this Magnet Demonstration Tube. Simply place circular magnets in the tube with their polarities switched and watch them levitate! Print Settings Printer: Da Vinci Jr. 1.0 ...
thingiverse
This rack does not have the easy remove-the-tubes-to-vortex ability of the commercial option, but since it costs about $20 print and fill with magnets versus $900, I think most people will find the trade-off acceptable! 1. <a...