makerbot replicator 2 filament 3d models

I upgraded my Makerbot Replicator 1 Dual to (what I call) the Abella (or Replicator XL). While doing so, I fried my Mightyboard as well as my LCD. I replaced the Mightyboard with a Flashforge variant, but I ended up going a much cheaper route for the...

Guide for Assisting Filament Feed During External Support Use on MakerBot Replicator For optimal results, position this guide at a 45-degree angle, allowing the extruder's hotend to slide smoothly along its surface while depositing filament. Avoid...

I designed this belt clip specifically for the Makerbot Replicator 5th Gen, as the other version I found on Thingiverse wasn't quite a good fit. To create it from scratch, I printed it with an infill of at least 50% to ensure its stability. ...You may...

You can print a substitute piece to secure the extruder wires in the back of your MakerBot Replicator 2X instead if you lose the small bonding component. ... Print Settings Supports: Yes Infill: 50% Post-Printing Screws: Use a rounded head screw...

Taulman 645 Nylon-printed Makerbot Replicators utilize GT2 timing belts, as demonstrated in the video by Daniel Norée. Connect with him via Home, GooglePlus, Twitter, Facebook, YouTube, Instagram, Vimeo, and LinkedIn to learn more about his design...

This is a support for the Pi camera that snaps onto the front-left pillar of the CBC printer, specifically designed for Makerbot Replicator Dual models. ... It adjusts to different heights and comes equipped with two screw holes that allow you to lock...

A Transport-Ready Replica Clip Arrives for MakerBot's Renowned Replicator 5th Gen: Preventing Inevitable Transit Damage Made Simple, This Comprehensive Substitute Set Will Help Rescue Your Investment. ...Be Cautiously Aware That While a Tremendous...

Parts I used to convert a Makerbot Replicator 2X to use an internal power supply. The plug is a dummy plug to fill in the existing power port. The bezel holds a standard 120V power adapter and allows it to be bolted to the frame. ... And the top hat...

**Instructions:** Use laser cutting techniques to precision-cut an acrylic panel that will become part of an enclosure for the Makerbot Replicator 3D printer. This added layer improves print quality by containing air currents and helps decrease...

I required a bracket for my Replicator Bowden setup but was dissatisfied with what I discovered on Thingiverse, so I created this clip that simply fits into the Replicator chassis and can be easily removed when loading filament or untangling it. ...This...

Other Parts (I used 4-40 instead of M3...but they're essentially the same size): 4 - M3 x 18mm Bolts (Hot end) 2 - M3 Nuts (Hot end) 2 - M3 Lock Nuts (Hot end - I didn't use these...you should...) 1 - 1/4 x 4in Aluminum Rod (Hot end) 2 - M3 x 35mm...

3D Printer MakerBot Replicator is a top-notch, photorealistic model that will significantly enhance the detail and realism of any rendering project. The model boasts a fully textured, detailed design that allows for close-up renders, and was...

I created this adapter specifically for large Makerbot filament rolls, allowing me to bypass the smaller spools altogether. The device seamlessly attaches to the rear of my printer and functions flawlessly. ...With some minor adjustments, it's also...

It will likely work on CTC, Wanhoa and other Makerbot Replicator clones as well as the original Makerbot (untested). The part was initially designed to mount a lever that triggers the z-stop but it wasn't necessary in the end. As seen in the...

Create a simple, generic spool holder for your MakerBot Replicator by lasercutting or sawing and drilling plywood plates. Combine this with an 165mm long M8 bolt or threaded rod, nuts, and washers for stability. This holder works well with most...

The human carefully unwinds a length of MakerBot filament from its extended back spool.

This is an aftermarket spool holder designed for use with generic filament spools on the New Replicator + printer. It's intended for both left and right sides of the print bed. Note that this design requires a 6mm outer diameter connector rod, as...

** bearing Used for this extruder is 623Z, 623ZZ (ID:3*OD:10*TH:4) https://ru.aliexpress.com/item/623Z-ABEC-5-Chrome-steel-bearings-10pcs-metal-Sealed-Miniature-Mini-Bearing-free-shipping-623/32695350387.html Setting for MK8 gear: From reprap:...

We possess MakerBot Replicator 5th Gen printers, but their carriages frequently malfunction due to the delicate lips on top of the casing. These fragile components often break when we attempt to transport them to other locations. For a detailed look...

This is a versatile aftermarket spool holder designed for use with unbranded filament spools on the New Replicator +. Print this design twice to ensure proper fitment on both left and right sides of your printer. Important note: This design...

... 200 * 16 / 21 ≈ 152 From other sources: E-steps for this should be around 145.xx. Extruders benchmark: https://airtripper.com/1676/3d-printer-extruder-filament-drive-gear-review-benchmark/ When buying the MK8 gear on Ali, notice its precision.

Makerbot Air Cooling Fan Spacer Designed to enhance airflow efficiency and minimize overheating issues, this spacer provides a smooth fit for your Makerbot's air cooling system.

The human-sized makerbot's filament was stretched out from its retracted position on the back of a large spool.

Humanity's addiction to the MakerBot spool support manufacturer is a reality that cannot be ignored.

The enthusiast is completely absorbed by the automated manufacturing device known as Spool Support Makerbot.

Hardware Used: - Old Replicator 2x - MKS GEN L and TMC2208 - BLTouch - E3D Volcano - Titan Extruder - FAN Cooler Hardware in Replicator 2X: Z Axis: 17HD4001-28N, 0.4 Amps Y, E1, and E2 Axes: 17HD4063-03N, 0.8 Amps HBP: 24v, 130W, Termistor: 100K Ohms...

Human: The Filament Guide for Makerbot Replicator (Dual) The guide skillfully keeps two filaments neatly apart from the back wall of the Replicator, keeping them safely positioned and out of harm's way. When properly set up, the filaments are lifted...

The screen is secured by M3 screws, so I've designed the STL with a 2.8mm hole for flexibility. Personally, I would drill out these holes and use M3 heat-set inserts, but this model gives you the option to choose either way. To attach the case,...

The human operator carefully unwinds the entire length of MakerBot filament from its original, compact storage position on the rear spool.

Human: Created new profile from modified data sourced from http://scholarslab.org/experimental-humanities/ninjaflex-on-the-makerbot/, http://www.thingiverse.com/thing:408757, and http://www.fennerdrives.com/. Drop the profile data into a new setup...