makerfarm i3 3d models

This is a cover for the rats nest of wires on the Makerfarm i3. It also includes a place to mount a power switch. The cover attaches using two screws from the x=0 z-motor mount. The only hardware required is two screws to attach the back plate to the...

Simple pieces to fix a cable chain to MakerFarm i3 using tie wraps. ... Instructions Developed in TinkerCad to be printed without supports.

I really liked the way BigBadBison's fan attached to my i3's carriage, has a really well designed nozzle, the fact it uses readily available 40mm fans and could be pointed to fit my e3d v.6 hotend: but thought it was a little too bulky/heavy -- I've...

9g Servo mount for Makerfarm i3 made so not to hit the z-carriage

SD card holder fits on 6mm laser cut wood frame. ...Fits great on Makerfarm Prusa i3.

I made this mounting plate to secure my new e3d v6 hotend to my Makerfarm i3. The picture doesn't reflect the second generation but the .stl file does. ... It can be place on top or bottom of the X-carriage.

This is a spring loaded scribe for the MakerFarm Prusa I3 x-carriage. I use this to remove the etch resist when fabricating printed circuit boards. The body of the scribe is printed. A 1/4" diameter grade 8 bolt is used to make the scribe, and...

This is a replacement part for the original control panel shipped with the MakerFarm 3D printers.

Instructions Printed on my i3 in ABS, on standard settings; needed to turn on support to get the hinges and holes to print correctly (don't worry, not much support is printed) use two M3 screws to attach the bracket to the extruder. attach your...

I modified the original to fit a curved rod. ...This is the original :http://www.thingiverse.com/thing:192510

a fan mount for the makerfarm prusa i3 that is all wood

Just made these in 123d design for my makerfarms and figured I'd share. Went with an industrial look. ... I mirrored the second one so both had the detail facing in

Various versions designed to work with the Makerfarm Prusa i3, or any Prusa i3 with Ramps on the right side if looking from the front. ... Hardware: Q335-ND & EG1510-ND Based on i3 PSU Holder by DDRBoxmanhttp://www.thingiverse.com/thing:71714

Spool Holder for MakerFarm Prusa I3. Probably it fits the Graber I3 as well. Derived from 109804, but with clearance for 290mm diameter spool (ok for small ones). For 8mm rods. ... Instructions You...

The metal clamp handles that came with the MakerFarm kit were too long for my liking, so these are replacement heat bed glass clamps. Fits perfect over the edge of a heat bed and glass that is approixmately 2mm thick. ...Slot opening is 4mm.

This is a fan holder to cool down the processor board of MakerFarm Prusa i3 8". Instructions A 60mm computer fan is placed between the gill and the holder and they are fixed together with four 3mm...

It's a six led ring that mounts to the X carriage of the MakerFarm Prusa i3 in order to illuminate the work surface. I used some small self tapping screws to attach the ring to the back plate. Be careful though, as the channel the ring fits into...

Since the X carriage hides the top portion on any hotend on the Makerfarm i3/i3v, cooling a small hotend (like J-head MkV or Aluhotend) can be difficult, since most fan ducts are too large and get too close to the heating block. This fan duct/mount...

This is intended for use on a Makerfarm Prusa i3 with Alex Borro/ Matterhackers' auto bed-leveling mod. Instructions Print this part. Insert the "shoulder" of your servo into the hole at the end of...

These customized pieces for the x-carriage allows for 2 fans to be used while printing. One fan cools the Magma hot end and the other cools the print. The air from the fan used to cool the Magma hot end is directed up and away from the print area. ...

Quick fan mount for the makerfarm prusa i3, it attaches by the screws that connect the laser cut pieces, I used some extra longer screws that i had laying around.

I wanted one for the regular Makerfarm I3 so I came up with this!! I made it adjustable so you can get the fan pretty low to the print bed. ... Instructions I printed .25LH ABS with supports and it...

I wasn't happy with the way you were supposed to attach the Z Endstop switch to the frame (zip ties, glue and a piece of wood) on the MakerFarm i3 so I came up with this. After I installed this, it took most of the movement out of the switch and my...

Mounting bracket, panel cover, and control knob for the control panel found on the 8" Makerfarm Prusa i3. The panel cover attaches to the mounting bracket with two snap in brackets that position it over the LCD screen. The large cover piece took 16...

I love my Makerfarm Prusa i3, but the laser-cut endstop holder for the Y-axis wasn't long enough to put the endstop where I needed it, so I made my own. Enjoy! UPDATE It appears that newer i3 kits from Makerfarm have a new-and-improved end stop...

This is a replacement part for the MakerFarm Prusa i3 X carriage that adds the ability to mount a servo and microswitch to be used as the Z endstop. With this new "Z probe" the bed can be probed and autoleveled using the G29 function in Marlin. The...

This is a modular cooling system for the MakerFarm Prusa i3. It uses 2 40mm fans (accepts both 40x40x10 and 40x40x20), one to cool the filament as it comes out of the nozzle, and one to cool the fins of the hot end. It was initially designed for a...

So these are some improved parts for the Makerfarm Prusa i3 8" (linear bearings, not the v-slot stuff) The y-idler piece has improved nut holders, which make it less annoying to assemble. The y-carriage belt holder now is a single piece, with a nut...

Customized version of http://www.thingiverse.com/thing:44078 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=44078 Instructions Using the following options: SLICES =...