makita guide rail adapter 3d models

Bed to MGN 12 Linear Rai Adapter for the Y axis of a CR 10 Mini

The latest version of the top rail is available at this link: https://www.thingiverse.com/thing:3845327. I found that it fits perfectly on WE Glock slides using the standard rear sight screw, but compatibility with other designs requires further...

Magnetic picatinny adapter to mount a MantisX to the barrel weight of a Hämmerli 215 match pistol *** Magnetischer Picatinny Adapter zum Befestigen eines MantisX am Laufgewicht einer Hämmerli 215 Sportpistole

Magnetic picatinny adapter to mount a MantisX to the floor of the pistol grip of a Morini CM162EI air pistol *** Magnetischer Picatinny-Adapter zum Befestigen eines MantisX am Griffboden einer Morini CM162EI Luftpistole

An adapter that lets you mount a picatinny accessory (up to 8.5cm in length) to a standard GoPro mount.

Adapter for 22mm devices (switch, reset and etc...)STL file enclosed for 3D print (use high infill with PETG)

I required a mount for two linear rails to sit atop a 2020 aluminum profile, specifically designed for my Anet A2 printer. I took gkirdeikis' design as a starting point and remixed it: https://www.thingiverse.com/thing:3199345. ...To increase...

This is a DIN rail mount for an ABB 7-hole S6 terminal block. The terminal block snaps directly in place into the block. ...There is no release handle on the block as it is assumed to be inserted on the side permanently.

I'm too dependent on my Hydra v6 toolhead, I couldn't upgrade my x-axis to use a linear rail until I had worked out a way to use it with joinatividad's V2 remix. ... This worked out perfectly for me, hopefully it holds up.

100mm Rail

100mm Rail

Makita 3701 Router

Makita 3701 Router

#define Y_BED_SIZE 214 #Due to Hydra and Linear Rails -6 #define Z_MAX_POS 325 #Due to visible Z mod +25 You'll need the X end stop from here: https://www.thingiverse.com/thing:3646827/ I've included the file. I've already done the viewable nozzle...

The stock extruder carriage (see the second image) also includes a "belt gripper" that tightens a section of the GT2 belt against the linear rail carriage. Without this "gripper", the belt simply spins and fails to move the carriage. It's probably...

*** Update 12/13/2022 (rev5) *** - Increase clip engagement - Reduce clearance to goggle face (lower profile) - Optional "lite" version which is about 2/3 the amount of material to print Rev5 of HDZero Goggles rail mount attachment prints. Also...

... risers aswell! I've used 2mm outer brims to print it, but I have yet to try to print it without. Dimensions are: Total rail length: 167mm display screw holes distance (top to bottom): 115mm display screw holes distance (left to right): 157mm

I made this rail for my Baikal MP-651K Co2 powered airgun. I want to attach a laser sight and a small scope, but the Baikal MP-651K only features a small dovetail mount under the barrel. It is made with Tinkercad, so it could be a litte off here...

A slide on sheath to give the CM.126 a under barrel rail. You need to slide it off in order to get the battery in and out and it is a tight fit but does slide on and off. ... Not tested on the field yet but I've stuck a hefty light on it and thrown it...

... v2: The height of 13 mm is the rail height plus carriage. I also created a larger joint for the connector ptfe to compensate for the level difference, which works fine with v1. ... Available here: https://www.thingiverse.com/thing:2670774/#files

This allows you to mount an HY VFD to a DIN Rail. I have model HY02D211B but this probably has the same hole spacing as other models. Hole spacing is 111.775 mm between holes. It is designed for easy printing without supports. You need to print...

This is a adapter for a sbr12uu linear bearing block to cr10 base plate. ...This was made for a bed upgrade on a Tronxy x3 custom.

The original STL has errors and if printed is too narrow to fit the USB adapter. ...So I fixed the STL and made it a little wider.

A slide-on sheath is designed to add an under-barrel rail to the CM.126. To install or remove the battery, you must first slide the sheath off its secure position. Although it's a snug fit, the sheath does come on and off without any issues. ...So far,...

Basically ran into an issue where I couldn't mount the carriage to the rail block without the belt being skewed. Looked for a model and found this Warump's version. I liked it and decided to tweak it to my liking. I haven't printed it yet, but I'm...

Here's a rewritten version of the text in American English, written in an active voice, and optimized for a Flesch-Kincaid grade level score of 100%: Connecting the Midland Bowman to the Comtac stock requires an adapter. The earpiece is no longer...

Initially, I had acquired a DYS 3-axis gimbal but encountered issues with using its standard hooks, leading me to conceptualize and create an adapter that utilizes rubber dampeners for added stability and control. ...This specialized adapter was...

This is my first 3d project, so please be nice... I printed a spool holder with 2 set of BB guided slot, but I soon realized that this wasn't a safe transport system because spool could get out the rails and fall over the printer's bed. I was quite...

... be used to attach the piezo inside the adapter. It's crucial to avoid applying too much pressure to the screws holding the adapter to the carriage front. ...The goal is for the adapter to bend slightly but not so much that it affects print quality.

I made an adapter so the filament guide is in the front V track if you have installed a direct drive extruder