maleficent 3d model

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 pattern_element_overlap = 0 custom_top_port_x_position = -10 custom_bottom_outer_edge_chamfer_radius = .6...

For your Rubik's cube to keep the fluidity of its movements, it is necessary that the dimensions of the model are reproduced very precisely, and that your board can allow a first layer of 0.1 mm... Usually to deal with defects in the horizontality...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 custom_back_extra_port_y_position = 0 custom_top_port_corner_resolution = 8...

Just make sure to get the alignment correct before letting the glue set up!Notes:Raft:              YesSupports:    NoI've had the best luck printing these using a single-layer raft, with the part oriented...

As far as assembly is concerned, it's all pretty self-explanatory when you see the models, but here are a few tricks: Use as little wire as possible, but make sure you use good wire. The wires run from the grip and back, across the side of the...

The COMPLETE The Bloodhunt bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! The Bloodhunt Knights were the first Soulless Vampire troops to be sent to the mortal lands of...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

... tolerances must be around 2 tenths of a mm, it is not essential to use CNC systems. The pieces can be easily made by any turner or by a modeling enthusiast and their cost is quite acceptable. ... Criticisms, suggestions and changes are welcome!

I recommend using a shorter heat sink and/or a fanBe sure to choose a fan size that will not interfere with the height of your heat sinkFilament sensor fits without issueBondtech extruder fits without issueOnly other fitment issues I have heard have...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

I have since printed out another model in ABS which I am hoping will be more durable. PETG would be another more durable substrate to consider using. Special thanks to Jim Harmon at Keystone College and Emmitt Zugar at Salem Community College for...

I've uploaded the STEP files, so feel free to remix the system to fit your printer model! Just give me a shout-out because it took a lot of hours, dozens of printed iterations, and plenty of PLA. The IR Probe is mounted to the connector by design...

New version available: Please check out the new Ultra Flat Filamentholder model, now updated to be 8mm lower, more accurate, and faster printing :)\nFeatures of the Flat Filament Spool Holder\nJune 6th - Finally finished making it. Enjoy...

This is a model of a convenient sliding lid box with an easy to use locking mechanism consisting of a bump on the lid that keeps it securely closed. Note that for slim boxes the lid does not bend as much and the locking and unlocking may be a bit...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

And yes, I'm already working on another version to fit the standard width tank; it shouldn't be too difficult to scale it down from the XL model. I've also come up with an alternative design - a curved blade that's just as effective but looks much...

I haven't printed it yet, but the OpenSCAD model turned out pretty well. See the additional .scad file, .stl and the explanatory symbols image. The original bezel is dark grey with a textured interior except for the plinth and label obrounds. This...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 40 printer_tolerance = 0.4...

In order to stay within bed size, put your skirt 0mm to the model. Once printed, remove the support material and clean up with sandpaper. Step 2: Print 2 Simple Metal Spool axle holders, same Splic3r settings as above. You can print both of them on...

It is intended to be loosely attached, for quick removal during total eclipse photography, and as a result, may not remain well attached in a windy or gusty environment.Materials neededPLA or another rigid filament for the frame pieces.Flexible...

On the single phase motor models there's contactors and timers in there for the auto tapping function... if fitted. I wired the 12 volt psu's mains connection to the main switch of the mill, this is after the main fuse so it's protected by that,...

Use for reference) Hardware needed: Two 5015 blowers (get the correct voltage for your printer model). I recommend Sunon maglev. Europe: https://www.tme.eu/gb/details/mf50151vx-a99/dc12v-fans/sunon/mf50151vx-b00u-a99/. A suitable connector to the...

I considered adjusting the model but decided to leave it as is, as I'd rather have a more positive engagement that you can adjust to your liking than end up with one that doesn't latch in place securely enough. I'll leave this marked as a work in...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

You can use a polarity detector app on your smartphone to figure out which side is North (+) and which is South (-).If you want to risk glue breaking loose and would rather not print the magnets into the piece, then you can just grab the models and...

Note: I accidentally had two ⅔ marks on the outer ring in the original model. That has since been corrected but I haven't had a chance to print out a replacement, so the pictures still have the typo</p><h3>How to use</h3><p>Pick a measurement disk...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

Enjoy my Ulvheim Small Merchant House. It came from my Patreon February Release. Thanks to all my supporters and to Markus Kruse / Terrain4Print, creator of the Ulvheim City. This model is supportless as usual. :)</p> <p>Discover my Ulvheim Remixes...

Note: The X axis part is for the current model of the Geeetech I3 Pro printer that uses a metal plate on the X axis to support the linear bearings and extruder holder. When I was assembling my Geeetech I3 Pro C printer, I was struck by the fact...