malyan 3d printer
1840034 3d models found related to malyan 3d printer.cults3d
Just see maker zsonybrasco's before & after shots: http://www.thingiverse.com/make:198927 Here is a good, and short, article on 3D printer rigidity:http://dabbletron.com/why-is-rigidity-important-for-3d-printers/ To compliment this mod, have a look...
thingiverse
Just see maker zsonybrasco's before & after shots: http://www.thingiverse.com/make:198927 Here is a good, and short, article on 3D printer rigidity: http://dabbletron.com/why-is-rigidity-important-for-3d-printers/ To compliment this mod, have a look...
thingiverse
Adjustable Z-End Stopper. ... Printed in PLA.
thingiverse
Very Big Z braces for modifiaed Wanhao Duplicator i3, Cocoon Create, Maker Select, and Malyan M150 i3 3D printers. Mod only for advanced user. ...I do not advise on the creation of this mod.
prusaprinters
This is a upgrade mod to eliminate the front and back y-frame plates along with the cheap idler bracket and wimpy y-motor bracket. This mod gives you stronger y motor bracket and a better idler tension . Also changes the belt path to be perfectly...
thingiverse
The rest of the parts for the z braces can be found here: azza z brace: https://www.thingiverse.com/thing:921948 SWD2 rear z brace: https://www.thingiverse.com/thing:2391089 B.O.M-- 2020 Y frame upgrade Hardware needed: 2x-- 180mm 2020 extrusions...
thingiverse
... a dual color Z brace mod for my Monoprice maker select. ...I used Azza's original file and duplicated the "balls" to get my desired effect. The "balls" can also be used for the "PLUS" versions of these printers. ...You have 2 "balls" extra though.
thingiverse
This is spool guide that is a remix of Azza's top right part from the z brace and Floreos' spool guide (I just combined the two). If you want the guide to be on the left of your machine then just mirror the object. ... This uses a skateboard wheel...
thingiverse
Cover 3D printer. ...Safe the print object from dust and cold drafts. Fits to Malyan 3D printer, may fit other models.
thingiverse
This is an adapter for the cooler of 40mm fan mounting to Malyan M150 3D printer http://www.thingiverse.com/thing:936207
thingiverse
This is an easer way of fitting a rubber foot to your Malyan printer! I made 4 square blocks that simply fit the original corner feet and allow you to screw a rubber foot to each one. You can still get to the screw that holds the corner plate to the...
thingiverse
This is a hotend cooler for Malyan M150 - 3D printer, 30mm fan (original hotend fan) Print Settings Printer: Malyan M150 Rafts: No Supports: No Resolution: 0.2 Infill: 20% Notes: I used support in the design so it doesn't need support any more. I...
thingiverse
This is a bracket which clips to the side of the Monoprice Select Mini and Malyan M200 printer bed for securing the heater and thermistor cables when rerouting them from under the bed.
thingiverse
I recently bought a Malyan 3d printer, its my first. And while learning about how to use it and discovering the joys of prints not sticking at start and the importance of bed levelling I discovered the bed levelling knobs are hard to use. I...
thingiverse
This is a LED light bar for the Malyan M180 3D Printer. It snaps over the rear of the extruder carriage and locks into two of the four locating slots. It makes use of the 12V LED strips available from Hobbyking. These are available in various colors...