manisha model

All you will need are; 6x Orange 3mm LED, 2x White 5mm LED, 2x Orange 5mm LED, 2x Red 5mm LED.  The side door can also open and lock as you turn the door handle, small model hinges are required for this to function.  Polycarbonate sheets can be cut...

Each time I found that the support material came away beautifully… right up until I printed the final model. A tiny piece of the design broke off with the support (see pictures). Thankfully It's not an essential part. It's only there to keep the...

The code you want to stop at is M107Example of first portion [to copy and paste in a new document]:; generated by PrusaSlicer 2.4.2+win64 on 2022-05-19 at 22:12:52 UTC; ; external perimeters extrusion width = 0.45mm; perimeters extrusion width =...

- If you want to grab the models themselves to work from, you can find them on [Tinkercad](https://www.tinkercad.com/things/8FMTsI7lrLp) - If you have other ideas for ways you'd like to see the trusses mounted or accessories to have on the end, let...

2)The plastic for the case is about 0.5 kg (the lantern is large, it was made for a large candle) 3)2 hinges for caskets 15x21mm with self-tapping screws (included, sold on marketplaces) 4)a handle for the casket (you can print it, but I wanted...

current problems: - comments and filenames are mostly in German language - some of the mounting holes in the pcb are not at the exact right place - the pcb was designed with easyEDA and not with an open source program like KiCAD, which is compatible...

DescriptionThis is a fast and easy to print model to calibrate your new filament. It can be used to find the right settings for the extrusion factor to get the right wall thickness.</p><p>It is designed with a 0.86 mm wall thickness to meet the...

You could also use hex stock cut to the same size, which would increase the weight (since the center of the nuts is hollow) and improve the spin time, but also increases the amount of work that needs to be done in order to build these.The nuts must...

V1 arm is fine too, but there is a risk of collision with some models of head in very rare cases of high and wide prints prepare all parts power off the printer UNPLUG POWER CABLE! disconnect low voltage connector (2 wires) unscrew PSU from the...

V1 arm is fine too, but there is a risk of collision with some models of head in very rare cases of high and wide prints prepare all parts power off the printer UNPLUG POWER CABLE! unscrew PSU from the frame remove plastic cover of PSU cables ...

I think the steel should slide easily against most rigid plastics but better safe than sorry. Use Instructions: Print the model Remove the heat sink, tubes, retaining screws, and any heater or thermistor -- only the hot block and heat break should...

the thickness (diameter) of the shackle in the model is 6,5mm. edit3: Redesigned according to the padlock i had, which has the internal measurements within the locked shackle (hmax x w): 21+mm x 20+mm. Shackle thickness: 6.5mm. See V2.0. Aaaand,...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

*** UPDATE 30/06/2021 *** As lots of people have noticed, the original model is a ridiculous reducer at a ratio of about 3:1 from the original duct. I've now added a design that is much larger (labelled as "Full Size") and can be printed in three...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

First, I had to model the front of the display to accommodate the RepRap Discount Full Graphics Smart Controller and then I also decided it needed a back to protect the circuit board. Done... Then I decided to tackle the problem of mounting a...

By the way, even though adding a vertical ring might seem counterintuitive, it does provide added stability while still maintaining the original model's benefits: no need for supports, and you can print directly without worrying about brim or...

Larger or smaller screws can be used if you scale the model appropriately, such as M3x8 screws at 150% part scale. Note that buying in bulk from a specialist supplier is significantly cheaper per screw. There are two versions of the container: the...

Related models: Track connectors for wooden railway to Plarail (and other systems) https://www.thingiverse.com/thing:5024058 Various other items of rolling stock: https://www.thingiverse.com/densha/designs Note that many 0-gauge (O-gauge, 32mm...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_pattern_element_radius = 6 custom_top_port_corner_radius = 5 custom_back_extra_port_y_position = 30 pattern_line_thickness = 20...

- The barrel at the front stabilizes the cars but is limited in size, preventing some models from fitting inside. However, a vast majority should fit without issue. PRINTING: - I print the main body and shaft separately from each other, as well as...

First, the CHS engineering team used SolidWorks to develop and virtually test the function and strength of the device using 3D CAD Models. Second, the device was to big to be printed by GrabCAD, so the team took the big parts and broke them down...

Issues that I have with the design: In hand, the phone with my case (Model brand Apple silicone clone) on it fits snug. I can shake it vigorously upside-down and the phone doesn't fall out. However, After strapping it to the stem, the mount develops...

Larger or smaller screws can be used if you scale the model accordingly e.g. M3x8 screws at 150% part scale. Note: it's cheaper per screw if you buy in bulk from a specialist supplier. There are two versions of the container available, the standard...

Parts links below: NEJE 20W Laser Module DIY Kit Fengda PU airhose PC4-M6 Fitting 1/8" to 1/8" Transfer Connecter 1/8" fittings Quick Disconnect Quick Release Coupling Disconnect Adapter Quick Release Adaptor 1/4" to 1/8" Transfer Connecter PTFE...

I use washers between the skate bearing and the mount to give a little clearance for the spool holder to turn (I could probably model in a little bump out instead of using washers). For adjustable friction, I've added a simple bail that attaches...

Based on the code provided, it appears that you are trying to create a 3D model using Blender's API, Python, and NumPy. Here is a modified version of your code with some comments for clarity: ``` import bmesh import mathutils from numpy import...

(Rotate these angles accordingly if you rotate the model.) This way, you will have two layers of crossing extrusions in the spine folds. This makes for much stronger, long-lasting book hinges.</p><p>For<strong> print-on-print</strong> technique (used...

The left adapter does require a small alteration which I did with a pair of side cutters (the ones that came with my Ender 3) (see pictures): - Unscrew the four screws at the bottom (be careful these strip easily) - Gently pull back the white tabs...

Modeled after a 1915 candlestick phone, early versions had no dial because you just lifted the earpiece and clicked the lever a few times to get the operator's attention and told her the number or person you wanted to speak to. This is a fairly good...