maplin gopro 3d models

... ...http://www.thingiverse.com/apps/customizer/run?thing_id=40704 Instructions Using the following options: Font = write/orbitron.dxf ring_width = 7 ring_thickness = 2.4 message = Maplin Canary Wharf font_size = 10 ring_size = 18.14 font_spacing = 0

http://www.thingiverse.com/apps/customizer/run?thing_id=1204005 Instructions Using the following options: textSize = 8 ySize = 15 xSize = 45 textHeight = 2 holeDia = 3.5 myFont = Liberation Sans Narrow and Liberation Serif zSize = 3 myColor = yellow...

http://www.thingiverse.com/apps/customizer/run?thing_id=1204005 Instructions Using the following options: myText = Maplin zSize = 3 myFont = Liberation Sans Narrow and Liberation Serif holeDia = 3.5 textSize = 8 xSize = 45 textHeight = 2 myColor =...

A casing for the maplins digital clock kit.

                                                                                                                                                                                                                                                         ...

... http://www.thingiverse.com/thing:117519 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=117519 Instructions Using the following options: Your_Text = Maplin Text_Font = write/Letters.dxf Text_Size = 9 Text_Rotate = 0

These are dividers that fit in the cheap Maplin flightcase. I created them as the dividers that came with the case were short and easily popped out. The new design makes sure everything says in its correct place! ... ...

I made this for a Maplin Flight Box (the one that opens sideways and into little compartments) I like all my screws to be sorted properly but there wasn't enough so I made a quick design in Sketchup. ...Print this flat for best results.

Customized version of http://www.thingiverse.com/thing:340321 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=340321 Instructions Using the following options: Name = MAPLIN BlockWidth = 2 BlockLength = 5

... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=117519 Instructions Using the following options: Text_Rotate = 0 Text_Size = 5 Text_Font = write/Letters.dxf Your_Text = @Maplin_MSF

Customized version of http://www.thingiverse.com/thing:117519 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=117519 Instructions Using the following options:...

... generator kit. ...This is a case for the kit. The LEDS are mounted on standoffs, so they fit the case lid, and the circuit board mounted switches are actuated by "push rods". Link to kit -- http://www.maplin.co.uk/function-generator-kit-220045

Maplin N50EH pinpointer detector wall mount Mount holes approximately 5 cm apart Would imagine that it would fit the JEEMAK INTEY VISUA KKmoon or similar please comment if you try with any other brands it's always helpful for other makers.

OLED Bezel for Maplin vented PSU boxes such as: http://www.maplin.ie/p/vented-psu-enclosure-7-n09khhttp://www.maplin.co.uk/p/vented-psu-enclosure-8-n10kh The bezel fits in the opening for the power plug (I usually mount the display in there along...

This is a replacment kickstand Leg for the N96GY Weatherstation LCD from Maplin

This is a replacment kickstand Leg for the N96GY Weatherstation LCD from Maplin

Customized version of http://www.thingiverse.com/thing:117519 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=117519 Instructions Using the following options:...

Customized version of http://www.thingiverse.com/thing:117519 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=117519 Instructions Using the following options:...

Customized version of http://www.thingiverse.com/thing:117519 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=117519 Instructions Using the following options:...

<p>There is a cast in place plastic nut holding this soldering iron in place. Mine has split in one place. This is a push fit collar to hold the nut tight. Print in the highest temperature material available…</p><p>Don't push on too tight. ...If you...

The original Thing by bookmake was nearly a perfect fit for Maplin's "Minature Microswitch with Roller" (Maplin product code N97AQ), except the gap for the lever arm and roller wasn't quite right - didn't extend far enough towards the left. So, I...

GoPro

Caméra Gopro

GoPro Camera

gopro modulatory

GOPRO KEYSHOT

http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_bar_rod_d = 31 gopro_secondary_what = rod gopro_primary = double gopro_bar_screw_head_d = 6.2 gopro_rod_nut_od = 8.05...

http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_bar_th = 3.2 gopro_bar_screw_nut_d = 5.8 gopro_captive_rod_angle = 45 gopro_secondary_what = clamp gopro_bar_screw_head_d = 5.9...

This inlay can be used on the original GoPro Case (https://gopro.com/de/de/shop/mounts-accessories/replacement-hard-shell-camera-case/ABMIN-001.html) to fit all the stuff you need. ... The GoPro fits with the TPU Case.

Gopro 4 Mount Print Settings Printer Brand: Wanhao Printer: Wanhao Duplicator i3 Plus Resolution: 0.1 Infill: 100%