marble display stand 3d models

Use a raft if necessary. ...A sturdy skull base supports this intricate Lego Bionicle Mask stand. ...My print exhibited a slight separation when attaching the skull to its foundation, but applying some superglue will securely hold it in place.

A book stand meant for larger books, but will still work with standard book sizes (13cm width 20cm hight). can also be used for other things like a tablet stand. Print a one Right and one Left Truss and 2 support bars and glue them together as shown...

Designed with a downward-extending tab at the back, so coins can be displayed across the top of a whiteboard. The tab tucks down between the whiteboard and the wall for stability. ... Designed in OpenSCAD, open the .scad file attached and set the coin...

Tabletop or shelf display for your hockey pucks. ...Designed to showcase the puck upright and with as little distraction as possible&nbsp;</p><p>&nbsp;</p><p>Should be ok to print with as little as 5% gyroid infill.&nbsp;</p><p>&nbsp;</p><p>No supports...

This is a display wedge, co-star of famous e-learning youtube channel Forgotten weapons. Use it show off your nerf blasters! Mine are the carnyrex ones. Use cura's Fuzzy skin setting to get the felted look for the felt.stl piece on top. ...I used...

The connection between the lattepanda and display appears remarkably fragile, so this should significantly enhance its durability. If you have a touch display, you'll quickly notice that the black frames have varying thicknesses on each side; I...

Display a die and show 6 faces at once. assemble with... 20x20x1 mm mirror : 3pcs 20x15x1 mm mirror : 4pcs 20x20x1 mm glass : 2pcs 15x15x1 mm glass : 1 pcs 1mm glass/ mirror can cut with ordinary cutter. ...Then you just need to buy 20mm mirror/ glass...

A small iPod Display piece designed to be totally invisible when in use Size chart TV4 - 5th/6th Classic thin TV5 - 4th Classic thin, iPhone 3g TV6 - 3rd Classic thin TV7 - 5th Classic thick TV8 - 4th Classic thick TV9 - 3rd Classic thick

Display your products, it is a useful foot to show articles, redesign of the first exhibitor, a little more practical where it rests on a 30° base. ...I have used it on a scale of 500%, up to 700%, it runs 10 and does not take more than 1 hour at 500%.

Please note that these designs have been scaled to fit my display, which means the stacking extension will not work with these versions. ... The 4-knife design is approximately 4 inches tall (101.6mm), while the 5-knife design measures around 4.5...

I fashioned a new coin display based on a lone example I possess, which included a pedestal. ...To complete this design, I introduced a curved rim at the attaching point and tweaked the measurements to ensure smooth integration of all components.

Designed this to display some souvenir baseballs I’ve bought from various places. ...Sits on my work desk and works well!The black looks okay, but white could look good as well (designed to mostly resemble home plate)Please like if you think it’s cold ...

I wanted to show off my collection of vintage Motherboards so I created a display system that allows them to be mounted vertically in my glass showcase. The design relies on embedded nuts at the back for secure mounting. Don't forget to share your...

... section 90 degrees will have it rest against the "hook" components of the print bed, eliminating the need for support material altogether. Update: Two fresh upper sections have been added, positioning keychain faces forward for enhanced display.

This is a display wedge, co-star of famous e-learning youtube channel Forgotten weapons. Use it show off your nerf blasters! Mine are the carnyrex ones. Use cura's Fuzzy skin setting to get the felted look for the felt.stl piece on top. ...I used...

A cute earring display for any cat lovers out there. It prints in place with no supports, and it's made of 2 pieces- the base and the earring holder. If you print this, sharing pictures would be really appreciated! ... Check out my other designs, you...

This is a very simple playing card deck display that I designed. I ended up printing 5 of them and lining them up next to each other to accommodate all of my decks. I printed mine in two halves on their sides and then glued them together with...

... have one case. ... I found these glass panes with a diameter of 76.5x54mm and a thickness of 1.6mm, so i used these as the window. you can also use acrylic if you dont have that very specific size at home (who has). there i can display my old insert.

I created this for the vendors of shows so they can display an AR.It has a 3 degree angle for AR to be level.I print mine with 15% infill at .4 layer height and have zero issues on the item working.The only AR I found it has trouble with is a 20 inch...

... Guy Fawkes (Anonymous) mask. It was made to be used with various mask sizes and can be printed in sections or full scale. It will make a great way to display your printed mask. ... Check out my Predator mask and a wide range of printable masks here.

T800 Skull Display for rifles. Install 5mm LEDs to complete the appearance. Mount holes on base are sized to fit 1/4-20 or 6mm tapered screws. I picked up some micro prototyping PCBs and soldered a couple resistors, and LEDs. I also obtained a micro...

To minimise material yet create a consistent Trek look, I used some angular features and added 'STARFLEET' to the front of the stand. The slots lock the packaging in place with a 5 degree incline for best balance and presentation. ... If you consider...

To make the name stand out more, I highly recommend acrylic paint markers if you don't feel like switching out your filament mid print for coloring the letters. I am including the STL file if you want to remix it. If you do, please upload your design...

I wanted a stand to hold the album cover for whatever record was playing. This works great! I printed it with one face flat and tree supports. I might do a little light-weighting and upload a second version. ...Enjoy and share a pic if you print it.

I'm on the hunt for a straightforward stand that'll hold my lightsaber upright with ease. I envisioned it fitting snugly around my i3 in two effortless pieces. ...The result is a sturdy base that can effortlessly support not one, not two, but all three...

This stand was crafted specifically for my P08 made by DWM.\r\n\r\n* [DWM logo](https://www.thingiverse.com/thing:2908871)\r\n* [Mauser logo](https://www.thingiverse.com/thing:2908868)\r\n\r\nThe logos need to be scaled down perfectly to fit snugly...

... or in my shop-window. ... Sheets laying around on the desk are space-consuming and are not recognized well by customers. So I laminate the sheets and put them in a simple stand. It's stable, does not tilt and does not hide much of the sheets. ...

stand w/ pegs that allow to easily get fingers under car as to not lift up from body, or remove the pegs and this will space your MST RMX car so that the tires are just barely touching the surface but the shocks are all the way extended as to not...

Work in progress balisong stand, different versions hold 2, 4, 6, or 8 at a time. ... *IMPORTANT* Current size fits 15mm x 35mm, this fits MOST balisongs as seen in pictures but will NOT FIT: Kraken, BBBarfly, FlyTanium Lucha -- updated version with...

Knife stand for 6 pocket knifes, 4 part's to print, it just fit's together doesn't need any glue. It hold's any kind of pocket knife, weight of knife doesn't matter. ... I made few other design's check it out at -...