mario and the music box 3d models
3292292 3d models found related to mario and the music box.thingiverse
... printed this out, please go to this. This is just the box and will work with every other part you have printed out. http://www.thingiverse.com/thing:72790 Customized version of http://www.thingiverse.com/thing:53235 Created with Customizer!
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=53235 Instructions Using the following options: musicAxisHolderH = 3.4 teethHolderH = 5 teethHolderW = 5 midGearAngle = -5 MusicCylinderName = Super Mario Underground GENERATE_CRANK_GEAR = 1...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=53235 Instructions Using the following options: E_PLA = 8240000 musicAxisHolderH = 3.4 MusicCylinderNameFont = write/Letters.dxf midAxisHolderH = 3.3 ro_PLA = 924 crankSlack = 0.2...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=53235 Instructions Using the following options: epsilonCSG = 0.1 MusicCylinderName = test song crankLength = 18 gammaTooth = 1.875 snapAxisSlack = 0.35 gear_gap = 1 pulleySnapL = 1.2...
thingiverse
caja mario bros y joshi, forma parte de una colección sobre cajas de Mario no olvides visitar mi perfil y si quieres saber como se hacen este tipo de cajas aquí te dejo un video tutorial, también decir que las tapas a partir de 2mm puedes cambiar el...
grabcad
caja mario bros y joshi , forma parte de una colección sobre cajas de Mario no olvides visitar mi perfil y si quieres saber como se hacen este tipo de cajas aquí te dejo un video tutorial, también decir que las tapas a partir de 2mm puedes cambiar el...
thingiverse
caja mario bros y joshi , forma parte de una colección sobre cajas de Mario no olvides visitar mi perfil y si quieres saber como se hacen este tipo de cajas aquí te dejo un video tutorial, también decir que las tapas a partir de 2mm puedes cambiar el...
prusaprinters
caja mario bros y joshi , forma parte de una colección sobre cajas de Mario no olvides visitar mi perfil y si quieres saber como se hacen este tipo de cajas aquí te dejo un video tutorial, también decir que las tapas a partir de 2mm puedes cambiar el...
cults3d
THIS MODEL CONSISTS OF THE MAIN BODY, THE LID AND A BACK COVER THAT ALLOWS YOU TO HAVE A SMALLER COMPARTMENT AND SEPARATE IT FROM THE BULKY. ... YAHU
thingiverse
... and Locket. ...It comes in three sections. The music box holder. A partition to cover the music box and a locket lid. ...At this moment in time there is no locking mechanism and you will need a locking rivet to go down the center of the swing latch.
sketchfab
Brass and wood music box Modeled in 3DS Max and textured in Photoshop.
thingiverse
Servo motor gears require a little bit of "solder setting" (a little trick I discovered: cut a small brass nail less than the width of the gear and use a soldering iron to heat up the nail as you press it into place attaching the gear to the servo)....
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=53235 Instructions Using the following options: gear_gap = 1 crankTeeth = 8 GENERATE_CASE = 1 crankAxisHolderH = 1.55 MusicCylinderNameFontSize = 8 pteethMinD = 1.5 crankAxisR = 3 midAxisHolderH...
thingiverse
This is "The Music Box" it's a hard case you can keep on your OP-Z at all times! This was made in collaboration with my cad wizard Riley (he did all of the work I just told him what to look out for) and me Axel, Space Cowboy for the Teenage...
thingiverse
(As a music box) (For the moment I have not finished the two drums) The drums are very simple pieces to model (I can give you different dimentions if you want) and you can easily make yours to your unique little melody! Send me a message if you...
thingiverse
set print perimeter width to .7 single wall for maximum efficiency. ...Holds 8 cartridges. The lid works for both.
cults3d
here is my Mario and Toad from the trailer of the movie super Mario bros. This Easter includes 3 versions of Mario 3 versions of Toad as well as 9 mushroom and its decor. I invite you to print Mario and Toad in resin, and the decor in pla. Do not...
thingiverse
This is a modular question and exclamation box, from the Mario Bross franchise. It's a little bit rounded, to make a "modern" reference from 8/16 bits Mario games. The pins can be glued, if necessary. ... It can be stackable horizontally using the edge...
thingiverse
The bottom section allows for the screws to be added through the wooden bottom from below and the floor of the music box which then also fixes the music box to the wooden box, no glue. The top part of the music box is then super glued into place. I...
thingiverse
This is a music box that uses a um66 music chip, Ldr (light dependent resistor), a speaker, and a etc. when turned and opened it starts to play music and the 3d printed version of myself starts to spin. It was made using multiple programs. ...
grabcad
The box also can be locked by a stick where I made a small hole on the top of the box.This link here is a recommend DIY music core size fit to this design:...