mario the music box 3d models

http://www.thingiverse.com/apps/customizer/run?thing_id=53235 Instructions Using the following options: musicAxisHolderH = 3.4 ro_PLA = 924 MusicCylinderNameFont = write/Letters.dxf E_PLA = 8240000 midAxisHolderH = 3.3 musicCylinderTeeth = 24 gearH =...

http://www.thingiverse.com/apps/customizer/run?thing_id=53235 Instructions Using the following options: musicAxisHolderH = 3.4 teethHolderH = 5 teethHolderW = 5 midGearAngle = -5 MusicCylinderName = Super Mario Underground GENERATE_CRANK_GEAR = 1...

http://www.thingiverse.com/apps/customizer/run?thing_id=53235 Instructions Using the following options: E_PLA = 8240000 musicAxisHolderH = 3.4 MusicCylinderNameFont = write/Letters.dxf midAxisHolderH = 3.3 ro_PLA = 924 crankSlack = 0.2...

http://www.thingiverse.com/apps/customizer/run?thing_id=53235 Instructions Using the following options: epsilonCSG = 0.1 MusicCylinderName = test song crankLength = 18 gammaTooth = 1.875 snapAxisSlack = 0.35 gear_gap = 1 pulleySnapL = 1.2...

Servo motor gears require a little bit of "solder setting" (a little trick I discovered: cut a small brass nail less than the width of the gear and use a soldering iron to heat up the nail as you press it into place attaching the gear to the servo)....

This is "The Music Box" it's a hard case you can keep on your OP-Z at all times! This was made in collaboration with my cad wizard Riley (he did all of the work I just told him what to look out for) and me Axel, Space Cowboy for the Teenage...

(As a music box) (For the moment I have not finished the two drums) The drums are very simple pieces to model (I can give you different dimentions if you want) and you can easily make yours to your unique little melody! Send me a message if you...

Music Box

scan from music box

This house for music box

Portable music box for parties.

This is a music box for Alfred Knobler hurdy gurdy. ... Attach the

A music box I made with Blender.

Mario Box with 3DSMAX

Box de Mario Bross

Super Mario Box

The bottom section allows for the screws to be added through the wooden bottom from below and the floor of the music box which then also fixes the music box to the wooden box, no glue. The top part of the music box is then super glued into place. I...

Cute music box as a gift for childern.

the music box from the demo of gloomwood, made from scatch while i was playing through it with a gun only run

The inlay on the front of the box is the engraving on the One Ring from the Lord of the Rings. ...The top inlay is a map of constellations. The mechanism of the music box has a 36 pin cylinder.

This is a music box that uses a um66 music chip, Ldr (light dependent resistor), a speaker, and a etc. when turned and opened it starts to play music and the 3d printed version of myself starts to spin. It was made using multiple programs. ...

id_mario_box_question ---------- X4 id_mario_box_screws ----------X16 id_mario_box_cover ----------X1 id_mario_box_body ----------X1

id_mario_box_question ---------- X4id_mario_box_screws ----------X16id_mario_box_cover ----------X1id_mario_box_body ----------X1

id_mario_box_question ---------- X4 id_mario_box_screws ----------X16 id_mario_box_cover ----------X1 id_mario_box_body ----------X1

The box also can be locked by a stick where I made a small hole on the top of the box.This link here is a recommend DIY music core size fit to this design:...

I adjusted this music box in order to watch movies on my smartphone.

this is an example of music box do with arduino and buzzer

A music box made of a small wooden chest. ...Great for gift

Found these music box mechanisms for relatively cheap. Similar ones on Amazon here:...

http://www.thingiverse.com/apps/customizer/run?thing_id=53235 Instructions Using the following options: MusicCylinderName = In the Hall of the Mountain King MusicCylinderNamePosition = 0 midBigTeeth = 20 crankAxisHolderH = 1.55 gearH = 3...