marker pen holder 3d models
364446 3d models found related to marker pen holder.thingiverse
Designed it for 17mm chalk markers for a blackboard. ...Inspired by some gundam pen holders. ... I would like to add some key-hole holders to the back.
thingiverse
This custom designed marker holder holds five 11 mm diameter liquid chalk markers.
thingiverse
If you are not sure if your pen or marker will fit change holeCount to =1 and do a test print. Customized version of http://www.thingiverse.com/thing:1147882 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1147882 ...
thingiverse
I wanted a marker holder to make calibration easier / faster. It's really just a simple cube with a set screw. If your 3018 has the square hole in it for a laser, this should work for you. Set screw is just something I had laying around from...
youmagine
the 72mm is the best fit for my markers. ...Also make sure you print with support everywhere.
thingiverse
Hexagonal design pen holder and optional horizontal stand for Copic Markers (and similar sized pens - anything up to a regular sharpie). Staggered design allows easy pen selection. Can be used in vertical orientation for non-alcohol based pens...
thingiverse
A quick Pegboard Holder for these Marlin brand permanent markers. For pegboards with 5mm holes and 25mm apart from center point. ... SketchUp File Included.
thingiverse
I added a clip to my whiteboard marker pen holder and suddenly it attaches seurely to a belt. ...Whiteboard marker pen holder: http://www.thingiverse.com/thing:1259931
thingiverse
Pen holder for marking RC touring car bodies, that depending on the position where you use it varies the floor height of the pen tip from 7mm up to 10mm. ...For original Sharpie or pens that are around 18-19mm Original design by [Burak...
thingiverse
A Marker holder for six markers, in triangle shape. What make it different is the engineering, some very thin vertical gaps were added, so as to guide the slicer to route the lines as shown in the last photo. This will ensure a smooth surface and...
thingiverse
I added 10x2mm neodym magnet. ...Its for 5 Whiteboard Markers.
thingiverse
the walls are 0.8mm wide, enough to hold your pens and art supplies.. There is also a separate design without the more difficult to print Corrugated walls but uses a little more material (just a few grams). and will take an extra 30-60mins to print....
thingiverse
... walls set to 40-80mm/s. the walls are 0.8mm wide, enough to hold your pens and art supplies.. There is also a separate design of it with corrugated walls to give additional support whilst using less print material. ... Remixes more than welcome.
thingiverse
This is a pen holder for the 22 markers produced by Tiger. ... ------------------------------------------------------------------------------------------------------------------- IF YOU HAVE FOUND THIS USEFUL PLEASE LEAVE ME A LITTLE LIKE
thingiverse
Marker holder for whiteboards with a ~ 7 mm T-rail. Parts has to be glued together. German translation: Stiftehalter für Whiteboards mit einer ~ 7 mm T-Nut. ...Teile müssen zusammengeklebt werden.
thingiverse
Simple porte crayon, feutre et bic pour accrocher sur le frigo A simple pencil, marker and pen holder for the fridge Need 2 magnets 8*3mm changelog: - correction size magnet - add filet
thingiverse
... the pen hold onto the edge of the whiteboard. Works perfectly! The holder is attached to the marker by friction so it's easy to replace the marker at any time. ...I've made a version with belt clip as well: http://www.thingiverse.com/thing:1323181
thingiverse
This Desk holder is for crafters to hold their Copic markers while working on their paper craft projects.
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=1401060 Instructions Using the following options: holder_thickness = 3 rotz = -60 roty = 0 rotx = 30 tube_bottom_thickness = 1 pen_radius = 12 big_number = 100 holder_height = 30 holder_radius =...
thingiverse
Ikea totebo magnet holder for flipchart / tableau svensas. ... 11mm holes for 10mm magnet With some hot glue
thingiverse
I was tired of using a rubber band to hold my fineliners together so I decided to design and print a little clip to hold them together. Inner diameter of the clips is 0.9mm. ... I recommend printing the first layer at a slower speed, and perhaps...
thingiverse
Customized version of http://www.thingiverse.com/thing:43406 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=43406
thingiverse
... without hunting. The marker holes measure 11mm in diameter. I am happy to upload a variation with different sized holes if requested. I would allow +0.5-1.0mm tolerance to your marker or pen diameter. ... Prints without the need for support.
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/2dQ2UQVLu6H
thingiverse
Remixed the "hook" component so it was large enough to hold the standard reMarkable marker, and the Staedtler Noris Digital pencil. *Note: This is _only_ the hooks section. ...You will need to download the other 2 parts from the original project: ...
thingiverse
Java-generated whiteboard marker holder meant for laser cutting or CNC milling. Works by hanging off a screw or also works fine free-standing because it has a wider base. Holds 9 large markers and 2 small ones, but it's trivial to edit the SVG and...
thingiverse
I needed a thing to organize my 50-piece set of Crayola Super Tip fine small-barrel markers and make them visible and easily accessible. This is a really minimalist design, simple and functional. Each slot is ~10mm diameter with good spacing between...
thingiverse
This is just a simple pen/marker holder for wall, whiteboard, window,...