marlin 2 0 0 for anycubic kossel linear plus w skr 1 3 and tmc2130 or tmc2209 by 3d models

I printed it out using the Anycubic Photon printer. ...It turned out great, I must say.

... A 10mm hole in front will fit any pneumatic fitting to guide your filament. STL and DXF files are available for cutting the plate with a laser or CNC milling. ...I built this plate myself, and it works perfectly - photos will be added soon!

Decided to build a filament holder featuring bearings that perfectly fit on the standard Kossel spool holder. The result exceeded expectations. The current diameter of the cylinder is 82mm, but it can be easily adjusted to suit various needs. ... To...

Bill of Materials: - 3* M3x16 Countersunk Bolts + 3*M3 Nuts - Bed - 3* M3 Nylon Nuts - Wheels - 6* M4x10 Bolts + 6* M4 T-Nuts - Mounts - Superglue, Loctite Instructions: - Countersink the Heat-Bed (If Using 240mm Glass) - Tighten 3 Countersunk Bed...

A replacement holder for the stubby stock one. ... The new card reels of my preferred supplier barely fitted and my 2.3KG reels certainly didn't. ... This comfortably seats both It simply replaces the existing part using the same bolts.

================================================== The goal is to create a corner cover, along with a heated bed holder and corner support, all in one piece - 3 in 1. Modified: 2018-04-06. The corner size has been repaired, and the bed holder...

I designed a unique layout for the stop or end key. It looks really good. ...The inscriptions are positioned perfectly, running all the way up to the top and supported firmly at the bottom.

These fit the 5mm arms on my AKLP perfectly, and I'm utilizing 12 of them with 6 springs - one spring at the top and one at the bottom of each set of arms. The 25mm springs I used can be found here:...

This makes it rock solid and provides a lot of structural strength as well by interlocking both halves around the V6. The other thing I did was to keep the stock fans. A radial fan just doesn't work for parts cooling with the restricted path. Right...

You can pass wires through the holes or use the holes as anchor points for wire ties or my little wire clips.\r\n\r\nI made a holder for my bore scope, a tiny camera inside a 10mm diameter housing.\r\n\r\nI created a stand for my effector with...

... standard stock holder. ... The new card reel spools from my trusted vendor fit snugly, but my 2.3KG reels did not fit at all. This comfortable solution accommodates both reels securely. ... It simply swaps out the original part with identical bolts.

... stock spool holder, easily mounts two 608 bearings. ...Print this item and connect one bearing to each clip. You can find the bearings I used at Amazon, listed as: https://www.amazon.com/gp/product/B01L7PCRB6/ref=oh_aui_detailpage_o01_s00?ie=UTF8&psc=1

I crafted some extra practice foam golf balls using my trusty CR10 3D printer and merged the two components into this innovative creation!\r\n\r\nUpdate: Version 2 was tweaked to ensure a snug fit, allowing the golf ball to rest securely within the...

... using these optical switches: https://www.thingiverse.com/thing:2210746, a fantastic resource. Meanwhile, the corner brace I've chosen is this one: https://www.thingiverse.com/thing:2918055, an excellent selection for added stability and support.

I essentially eliminated the stepper motor's cable hole from Trent White's design, as it wasn't necessary for my purposes and visually unappealing with a hole on each cover.

... - A notch has been added to securely hold the belt within the slider. - Unnecessary features were removed and cleaned up for a more streamlined print. ... - Small geometrical adjustments were made to make the print both stronger and easier.

I created a remix of this for hockey puck feet, but I didn't need the screw hole and shaved down the height a little bit on the puck covering. ...I also tightened up the grip so it would work with these and fit snugly without any additional hardware -...

If you want to relocate your SMPS below your printer by attaching legs, this is the project.

Bed clips for the ultrabase are designed to securely clamp it to the 3mm aluminum heatbed using its tiny bevel (6mmØ) around the outside. This lip provides just enough grip, eliminating the need for adhesive. The paper attached to the adhesive under...

After remixing one of Thingyverse's better ducts and creating a version that stands out due to its oddness, I decided to give it a proper try. The Plan: Make it compact and quick to print. Ensure all four screw holes are accessible. Optimize...

... magnetic rods to make contact with it. ...This becomes a significant issue in the magnetic version, where the rods' tendency to interfere with the fan is especially pronounced. To address this problem, I had to relocate the fan body upwards by 20mm.

I modeled this in 2019 from vernier caliper and other means of measurement from the real printer I purchased. This is the complete 3D printer, all parts, enough to reproduce. This is one of the best affordable Delta 3D printers ever produced. ...Some...

...This provides just enough of a lip for the clips to securely clamp the Ultrabase to the 3mm aluminium heatbed. Adhesive isn't required. I just left the paper attached to the adhesive under the Ultrabase. They sit flush with the top of the Ultrabase.

I changed the cross section of the hole for the axis of the stepper, so that the part fits better. Native bolts from an aluminum head fit into the holes of the fixing bolts, you don’t need to cut the thread, just carefully screw it into the plastic,...

custom knob for TFT 35 screen Feature: -6mm diameter -Could also be used for 6mm diameter potentiometer

The scraper is designed to catch loose glues and excess materials that accidentally fall from the print bed during operation, preventing them from getting on the printer's floor where they could be messy and interfere with printing.

Chollos 3D https://t.me/chollos3dMasQFilamentos COMUNIDAD CREALITY ENDER https://t.me/CrealityEnder3Original MAXUS MARLIN TMC_2208 en Standalone proteccion thermal runaway activa Sd suport activo para modulo externo Iconos fullgrafics de serie...

... that Octoprint doesn't work properly. For some reason the printer does not homing when I print with Octoprint and moves to the print bed. When I print from USB or SD this does not happen. So the gcode is ok. If anyone has an idea, let me know. ...

I cross-referenced online resources and conducted trial-and-error experiments to create a custom Marlin configuration file for Marlin 2.0. My next challenge was that this clone board didn't have a bootloader installed at the factory, so I couldn't...

These are Anycubic Kossel mounting brackets for SKR 1.3, SKR 1.4, MKS GEN L, and MKS SGEN mainboards, measuring 20cm in bed size. Mainboards with these specifications fit perfectly on these brackets inside the Anycubic Kossel printer with a 20cm bed...