marlin 2 0 anet a6 3d models

After considering modifications, I designed a holder specifically for the Anet A6 printer. To assemble it, you'll need both the original and a mirrored version of this design. In my case, these two versions worked perfectly without any additional...

For a fresh update on my personal website, visit https://www.designuitinspiratie.nl/anet-a6-z-hoogte-modificatie/\n\nYou know how it goes with 3D printing... ...:-)\nI'd made some modifications to the printer to print specific prints.\nThe modifications...

I wanted to minimize the noise emanating from my Anet A6 and identified the Y motor as its primary source. I decided to create a motor mount that could be printed in Flex/TPU to see if it would significantly reduce the noise levels. And, I was...

... I had to break the bottom out to make the screw holes of the motor align with the mounting holes. The cables to the controller are held by the “Anet A6 Cable holder X wagon”: https://www.myminifactory.com/object/anet-a6-cable-holder-x-wagen-34850

This is a vital safety upgrade for your Anet A6 printer to prevent electrical mishaps. It features a fused switch, which provides an additional layer of security. You can find the type of switch I used at Amazon:...

If you want better and faster printing, you need to make the Anet A6/A8 more rigid with a stiffer frame.One way of doing this, is to clamp/mount the y-carriage M8 rods to a solid base plate. The plate can be plywood or similar.</p><p>Most other...

An Y-Axis GT2 belt holder suitable for the heat bed frame holder from Bohrers Shop (https://shop.bohrers.de/heat-bed-holder-anet-a8-und-a6-kommt-in-kuerze.html) but it should also fit on the stock Anet H-frame (the holes do) and definitely on other...

An Y-Axis GT2 belt holder suitable for the heat bed frame holder from Bohrers Shop (https://shop.bohrers.de/heat-bed-holder-anet-a8-und-a6-kommt-in-kuerze.html) but it should also fit on the stock Anet H-frame (the holes do) and definitely on other...

Anet A6 Y-Axis Cable Chain ( https://www.thingiverse.com/thing:3625060 ) Because of vibrations during printing, I had a nozzle pop up and tear off details from the table, so I downloaded and printed a new nozzle...

I purchased two MOSFETs for my Anet A6 and initially planned to mount both above the mainboard, but Leo_N's design convinced me to install the hotbed MOSFET below the board using his horizontal version and the hot-end MOSFET above the board using his...

This modified carriage brings a fresh twist to the ANET A6 by housing the E3D V6 hotend using a bowden extruder. Designed with ease of use in mind, this carriage requires only a handful of screws for assembly and prints effortlessly with minimal...

... Fits an Anet A6 or A8 Printer or Other Printers with a 220x220mm Holder. There Are Two Different Versions Available: One with a 1mm Thickness and Another with a 3mm Thickness. Special Thanks to FedeMiller for Providing the Various File Formats.

One of these linear bearing replaces two LM8UU bearings for the Anet A6 or Anet A8 bed. It is intended to primarily remove noise, mechanical play and weight. It is made of only two parts: a housing and a snap in spiral bushing. Self threaded M4 holes...

UPGRADE JUN-14-2018 Added new STL for Thingiverse user COSIK to make the fanduct (https://www.thingiverse.com/thing:2013199 Anet A6 circular fan duct by Paclanc) fit. See comments for details UPGRADED NOV-24-2017 -support for x limit switch added...

(The orange printed carriage in the first picture was printed using an RPW-Ultra on an Anet A8 printer.) **Recommended Additions** * Anet A6 Adjustable Z End Stop For RPW-Ultra Carriage (https://www.thingiverse.com/thing:3299291) **Why do you...

Tronxy X5 Marlin 2.1.2 hybrid for MKS Gen L V1.0 board. Upgrade your Tronxy x5 using gen L v1. board by MKS. No issues with stepper control for now. A4988 and LV8729 Drivers used be sure to correct to the right ones !!! Don't forget to calibrate...

Trying to install an auto level sensor on my Anet A6.\nI managed to install it on the right-hand side from the front, but it blocked the X-axis going all the way to 220mm. This is another attempt - this time installing from the front using the fan...

The Anet A6 kit comes with the 40mm fan bolted directly against the cooling rib to keep the filament assembly drive securely in place. However, this design offers no support for the fan itself. To address this issue, I created a custom...

A Custom-Made Bracket for the Anet A6 Fan Mount, Designed Specifically with the Proximity Sensor SN04-N in Mind This innovative replacement bracket is tailored to accommodate the small square inductive sensor known as the SN04-N, ensuring seamless...

I'm stoked to share my first creation :)\r\n\r\nThis is a nifty camera mount designed specifically for securing under the heated bed of your Anet A6. To attach it to the frame of the bed, you'll need a trusty zip tie.\r\nI personally use it in...

As I envisioned improvements, I decided to adapt the design for my Anet A6 by creating a holder that pairs perfectly with the original and a mirrored version. To ensure seamless integration, both versions work without any support required. ...If you're...

Y axis reinforcement for Anet A6 version 2017. Indeed, I had found another one and the position of the square inserts in the front plate were not in the right position on mine. You will need to measure your M6 threaded rod lengths: one long and one...

The popular cover for Anet A8 and A6 power wiring features a cutout specifically designed to accommodate a fan. The main cooling surface of the power supply is its aluminum backplate, which plays a crucial role in dissipating heat. When you install...

I designed a custom "pillar" specifically for mounting motherboards on the Anet A6 and A8 printers. This project allows you to choose from various colors or replace one if it breaks. The pillar's dimensions make it suitable for other boards, with a...

This is a very easy timing belt tensioner that I designed for the ANET A6 Prusa (it should work on any 6mm GT2 timing belt). Hand drawn, extremely strong. Print ABS with 100% infill. Use the clip on the other side, also with 100% infill. I used PLA...

This is a custom dust cover for the Anet A6's Z-axis stepper motors, designed with precision in mind. Upon completion of the printing process, slight adjustments may be necessary to ensure a perfect fit. To make these adjustments, tools such as...

I designed custom MOSFET switches for my Anet A6 3D printer's extruder and hotbed, both located underneath the S-240-12 PSU. The cover features strategically placed holes for efficient cooling and accommodates a 40x40 cooler. I utilized an IEC 320...

This is an adapter to install the Anet A6 display on a Monoprice Select Mini. The pictures explain the assembly. I'm using M3 screws here. Unfortunately, the original turning wheel cannot be used. Please print another one. ...I added the turning wheel...

First of all, it is intended to be mounted on the stock Anet A6 Z carriage. It features a modified version of the Z Axis endstop bumper with an added X endstop mount. I've made it compatible with Xalky's titan extruder mount as his carriage does...

This is a remix for the Anet A6 - Frankenstein found here https://www.thingiverse.com/thing:1692794 I created this model after discovering that a 40mm axial fan didn't provide sufficient airflow, so I decided to try it with one 50mm radial fan and...