marlin 2 0 anet a6 3d models

Motor Mount for Plates: Check out this design on Thingiverse: https://www.thingiverse.com/thing:2364937 This mount doesn't include a thread (M6) for the Teflon tube fitting, so you'll need to screw it tightly into the 5mm plastic hole. ... It's...

Converting the carriage from https://www.thingiverse.com/thing:2769635 to https://www.thingiverse.com/thing:2171816 required a straightforward process. ...To accomplish this, I needed to swap out the fan and use a strong adhesive called Attak glue to...

Do not hesitate to replace the Chinese hotbed plug immediately, it's a menace waiting to strike! It's a ticking time bomb! So if you don't want a fire in your home, remove the plug and connect wires directly to the hotbed. This strain relief will...

When I upgraded my X Axis group using the model from https://www.thingiverse.com/thing:2043600, the Z endstop required a fresh support system to function properly. I experimented with https://www.thingiverse.com/thing:2242931, which performed well...

Remix of https://www.thingiverse.com/thing:2471266 Printing quality greatly depends on ensuring that the carriage rails are perfectly parallel to the bed. The caliper's stability and resistance to movement have been significantly improved thanks to...

To assemble the Z-axis, attach the auto-leveling holder. ...However, since there's limited space, you'll need to join "right_inner_x_rod_brace_remix" and "right_z_carriage_remix" using glue instead of screws.

This is an elementary cover for the power supply unit. It's engineered to replace the basic electrical connection with a IEC320 connector. To assemble this project, you'll need to drill holes for the screws and strongly recommend gluing the parts in...

An Effective Way to Keep Your Extruder Motor at a Safe Temperature! Printing with ABS or PET-G materials often results in high temperatures, which is detrimental to the extruder motor's performance. As it stands, this vital component operates in an...

A couple of sketches were created, an authentic front panel and a revised one due to the thin edge near the rod mounts. ...The design was specifically tailored for the Y-Belt tensioner: https://www.thingiverse.com/thing:1959208 Be cautious with the...

(BTC) 1NRKRy4iYxTLzsQ6Dkm5BYJW1wqzQiYYjT (ETH) 0x2a7ff57de153203068b6310Cb5223482501a90EC Thanks for the transaction!

This is a collection of upgrades to the printer that stands on a sheet of expanded polyethylene foam for less noise. The setup has no internal stresses, so it doesn't need to be fixed to a basis. The power supply casing isn't included because my...

Be extremely cautious - this device can shatter your front and rear plates at any moment. The front clamp is compatible with the following model: https://www.thingiverse.com/thing:1896013. The rear clamp, on the other hand, requires the specific...

Modification of the original piece adding a final cap on the left side for the car's end stop.

06/12/2017 V6. -Vent holes are now wider. 19/06/2017 V5. -Fixed wrong angle that caused bad printings. Now is 45° 19/06/2017 V4. -The Nozzle is now centered. -Added more holes and -Added a version with a space to see printing. -Added original...

A fun faceplate to upgrade your printer's look instantly. ...Made from durable 1.5mm thick material, it fits perfectly with the original equipment without any issues.

I designed a cap specifically to fit the Z rod. ...The other models I tried failed to work out, so I built this one, which becomes stuck on the screw, rendering it immovable.

The technician precisely adjusted the rod's length to achieve a perfect fit.

Vibration suppressors are employed to mitigate the adverse effects of resonant frequencies on equipment and structures. ...These devices function by absorbing or redirecting vibrational energy, thereby reducing the amplitude of oscillations and...

I downloaded https://www.thingiverse.com/thing:2487759, but unfortunately, it came out a tad too small for my needs. The ends wouldn't wrap neatly around the frame, so I decided to extend it slightly. ...Despite this adjustment, one side still has 3mm...

Printing ABS or PET-G filaments can cause the Extruder motor to overheat, leading to decreased performance. If your printer is enclosed, this issue is exacerbated by the hot environment surrounding the motor. To mitigate this problem, consider active...

Holder for filament runout sensor switch attachment. Directly attached to a direct drive extruder, this holder takes up no extra space. Securely held in place using the existing nut and bolt combination already on hand. ...No additional screw holes...

I'm searching for a carriage that pairs well with a BMG extruder and V6 hotend. The top-rated option I've discovered so far is the https://www.thingiverse.com/thing:3202047 model. After modifying it to suit a standard dual-gear BMG extruder, I was...

I had to secure the Z-axis motors with a sturdy attachment system that allowed for easy screwing to the base. I've redesigned the ejpsx project from scratch, resulting in a rock-solid Z axis motor mounting setup. ... Update 2018-04-15 23:00 I corrected...

Here is the new 480W power supply with a switch, featuring a power socket and fuse. This design is specifically for the S-480-12 model, which requires 150x50 mounting holes. ...To prepare the base plate, carefully drill three identical holes using a...

To stabilize the Z wobble, a supportive framework is needed for the Z-axis rods. ...The V2 model introduces a spiral-shaped design that securely holds linear bearings in place along the Z-axis rods.

I wanted a better fan fixing option but found that the cable management feature was fouling on the frame so I've removed it. ... Category: 3D Printer Accessories

Fits snugly to the left of the extruder head, taking up space just before the X-Stop limit.\r\n\r\nNecessary Items:\r\n2 M3 screws, each approximately 15mm in length \r\n2 M3 nuts \r\n2 small zip ties.

Subscribe now to stay up-to-date on the latest news and updates! ...https://youtu.be/V-q_PJ_qY5Y Get ready for an upgraded version of this amazing creation - check out the second version here: https://www.thingiverse.com/thing:2340193

You require just four rubber bands to get started.