masterbox q300l 3d models

This is a mounting bracket for a second 3.5 HDD that can be installed in your Cooler Master Masterbox Q300L. Story: I'm building an HTPC and needed another 3.5 HDD to install in my case. The original design only allows one 3.5 HDD, so I created this...

I designed this bracket specifically for a Cooler Master Masterbox Q300L, providing an additional mounting point for a second 3.5-inch hard drive. Originally, the case only accommodated one 3.5-inch HDD, so I created a bracket to fit in front of the...

This is a fantastic headphone holder designed specifically for the CoolerMaster Masterbox Q300L case. It easily screws in from the bottom and perfectly aligns with various combinations of holes on the top. So you can place it more towards the...

Q300L was one of the smallest and lightest cases and it was super cheap (so there's little regret on modding it). But I really wanted a handle so I just made one. For this one you'll need 4x M5x30 screws (M5x25 will also work) and 4x M5 nuts. ...

The Q300L has clip-on plastic bars in every corner that can be taken out and swapped around as neccessary for your case configuration. This thing replaces one of those bars with a custom one with mount holes. I've used it to add a headphone holder...

The Q300L has clip-on plastic bars in every corner that can be taken out and swapped around as neccessary for your case configuration. This thing replaces one of those bars with a custom one with mount holes. I've used it to add a headphone holder...

The Handle and Decoration Panel is a standout feature of the PC case Cooler Master MasterBox Q300, designed to add a touch of style to any setup. To install it, you'll need screws with a UNC thread size of 6-32 and a length of 5/8 inches - these can...

This is a computer case thingie to hide a computer PSU.

Extended height foot increases airflow from the bottom. Total height is 18.5mm, compared to around 8mm stock. To edit the design, visit onshape.com and access the public document. ...The document ID is 515a01c6f666f557669986df.

Mount four 3.5 inch hdd on a 140 mm fan mount. ...The extra 8 holes are for stability and works on Coolermaster Q300L and Q500L cases. ...Ender 3 v2 0.6 nozzle PETG Category: Computer

Mount four 3.5 inch hdd on a 140 mm fan mount. ...The extra 8 holes are for stability and works on Coolermaster Q300L and Q500L cases. ... Ender 3 v2 0.6 nozzle PETG

<p>Mount four 3.5 inch hdd on a 140 mm fan mount. ...The extra 8 holes are for stability and works on Coolermaster Q300L and Q500L cases. Ender 3 v2 0.6 nozzle PETG Category: Computer

<p>Thanks to <a href="https://www.thingiverse.com/Psych0o">Psych0o</a> on Thingiverse for the design and including the STEP file. ...I've simply modified it to support M3.</p><p><a...

Thanks to Psych0o on Thingiverse for the design and including the STEP file. ...I've simply modified it to support M3.https://www.thingiverse.com/thing:4565701 Here is the original design that supports M5 25-30.

A simple holder for earbuds. ... Category: Computer

<p>A simple holder for earbuds.</p> Category: Computer

A straightforward container designed to securely store earphones.

The masterbox Q300L doesn't have really good airflow because apparently the holes in the panels have bad spacing and the fans are basically attached to this panel, so even with 4 fans in the case I was still getting quite high temps. To alleviate...

This is a leg riser for the CoolerMaster Masterbox Q300L case. You will need 4 of these to fully raise the case off the floor. This was created to prevent the case from sitting on carpet, as the PSU intake is on the bottom. I was able to print...

This accessory is intended for use with any 120mm case fan, allowing it to be securely fastened to the front of the Cooler Master Masterbox Q300L PC case. By adding 10mm of clearance between the fan and the steel panel, it significantly reduces noise...

With these brackets you can extend number of attached 3.5" disks (default 2pcs) for Cooler Master MasterBox Q500L (Q300L) case. You can mount additional disk inside and outside of your case. ... (You will need 4 extra standard case fan screws to mount...

replacement front and top panels for coolermaster q300l pc case. They provide much better thermals than the factory panels. did not provide mounting holes as i wasn't sure of the hole spacing variance from case to case. extended front panel provides...

This is a rack for a set of head phones for the Cooler Master Q300L you may need to drill out the 4 holes you want to use for the pins with a 1/4 inch drill bit. ... their are holes in the back of the pins for you to stick a 3 inch piece of 1.75 mm...

Just a front panel for the masterbox 5 to get better air flow and lower temp

Easily snap the third fan into place at the front of your CoolerMaster MasterBox 5.

Compatible with Cooler Master's MasterBox NR200 and MasterBox NR200P.We are making free to print and modify the design for the clips that hold the paneling of our most beloved ITX enclosure(s)!Lost one? Your product is out of warranty?<br>No problem!...

... tried to make a copy fromt he one present in the case. The final result is quite good, and I've been used it to mount the second SSD. The original piece was this: https://www.cmstore.eu/spare-parts/masterbox-lite-5-k500l-mb500-rgb-ssd-bracket/

During the development of the Cooler Master MasterBox NR200P, we created several variants for the case feet design.&nbsp;Following numerous iterations, the launch design was chosen, but we thought "why not share the iterations with our users?"The...

During the development of the Cooler Master MasterBox NR200P, we created several variants for the case feet design.&nbsp;Following numerous iterations, the launch design was chosen, but we thought "why not share the iterations with our users?"The...

During the development of the Cooler Master MasterBox NR200P, we created several variants for the case feet design.&nbsp;Following numerous iterations, the launch design was chosen, but we thought "why not share the iterations with our users?"The...