mavic pro battery 3d models

Mavic pro battery cover that snaps in place rather than squeezing onto the battery connector.

Holder for Mavic Pro batteries. ...You can join two holders with two m3 bolts and nuts.

Travel case for 2 DJI Mavic Pro batteries. ...Thanks to Nauseum for the Mavic Pro battery scan. ...I used it as a reference when creating this model.

Travel case for 2 DJI Mavic Pro batteries. ... Thanks to Nauseum for the Mavic Pro battery scan. ...I used it as a reference when creating this model.

A scan of a Mavic battery for a project

Battery cover for the Mavic Pro, I don't like storing my batties in the drone but the props need something to rest on so I've made this in its place.

Protection for the DJI Mavic battery connector. ==== I strongly recommend Flexible filament for a perfect fit ==== !!! ...Print Settings Printer Brand: Ultimaker ...

This is a battery holder / stand for the original DJI Mavic Pro batteries - It stores three neatly. ... It has a stepped design inside to match the battery profile.

a very simple 3D printed battery terminal cover for the DJI Mavic Pro batteries. Just to give it that extra protection :-) I have also added a version without the two "inner" tabs to make it more "printer / filament" friendly. Please fly...

German Bellow ---- DJI Mavic Pro battery pole protection cap This pole protection cap for the DJI Mavic Pro ensures that the electronic contacts of the battery (LiPo's) remain clean during transport, do not get damp, do not get a short shot or are...

Protect your battery from dust and dirt with this battery cover for Mavic Pro

I often transport my DJI Mavic Pro without a battery installed. This very simple filler prevents the propellers from being bent down when folded, and also (maybe) adds a bit of extra strength to the basic frame. The model was created by hand in...

This is a remix of http://www.thingiverse.com/thing:2137716 mount. ... It has a hole for the power button and also slots for battery straps.

This battery port cover is based off the charger port that comes with the Mavic.. It is to protect the leads from things touching them and starting a fire. I made it because I will be flying on many airlines with my Mavic, and wanted the ports...

I did not like how loose Noel's version fit and the fact that it had a lip on it on both sides so that it would not be flush with the front of the battery so I remixed it. I basically removed the lip from one side and made the channel narrower for a...

DJI mavic 2 pro battery case

Mavic 2 pro battery cover. Note the little corner in the inside. This should be matched with the corner on the battery connector when you push it on. I made a tight fit, so it won't fall off. ...

My Mavic Pro battery went bad - the "battery error cannot fly" meaning it just needed balancing properly but DJI considered it as scrap! So i took it apart, added a balance lead to charge it properly then remixed a battery cover to make a new holder...

Please See V2 if you require ones that show the charge state of the battery: https://www.thingiverse.com/thing:2405174 ----------------------- A very simple little battery clip to cover the fairly exposed battery contacts on the DJI Mavic Pro's...

......You may find other duo battery packs available but it doesn't work because there is not enough space between the batteries (I'm referring to this https://www.thingiverse.com/thing:2394779). ...Don't waste your time and plastic and enjoy this version.

Covers to protect the connectors of the drone and the battery. Printed in PTU with 50% infill. ...

... dust and water. Against the other models you can find, this one don't enlarge the outer dimensions of your battery pack. ... The cover is fitting tightly - You can easily dismount it with pull sidways and press a bit on the front with your thumb.

Note: R/C will no longer charge the iPhone, so be sure to have a phone with a healthy battery, however if the phone dies, you will still have connection to the drone and can continue to operate it either line of sight or for engaging the emergency...

https://youtu.be/T2AEHSYZt1U

https://youtu.be/T2AEHSYZt1U

... need to keep the terminals covered. ... You could use tape, but you risk getting gunky adhesive on the contacts. I found a design that said it was for the DJI Mavic 2 Pro, but when I printed, it did not quite fit. So, I made one that DOES! ...

A very simple little battery clip to cover the fairly exposed battery contacts on the DJI Mavic Pro's Battery. The clip is JUST big enough to fit over the contacts and the first time may take some pressure and trial and error to get it to go on,...

This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/3hCsVkaJfDU

Just a remix because the original does not clamp for me...

Just a remix because the original does not clamp for me...