maya 3d modeling

Print Settings Printer: Heavily modded Craftbot Rafts: No Supports: Yes Resolution: 0,15 or 0,20 mm Infill: 33 or 50 % Notes: Print both models in PETG with 3 mm thick walls and slightly hotter than usual, this should give you enough strength for a...

You could also use hex stock cut to the same size, which would increase the weight (since the center of the nuts is hollow) and improve the spin time, but also increases the amount of work that needs to be done in order to build these.The nuts must...

Furthermore I created the endstop mounts which are already present in the Fusion 360 model. I will try to update the pictures today or tomorrow. Now it gets exiting! Electronics are next! **Update 9** (03.07.2018): After test driving the Z-Axis I...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_x_position = 20 custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 42 custom_bottom_fillet_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_mirror = 0 stencil_drawing =...

... Norrick      Details: Gravemaw is standing around 145mm tall on a 60mm customized base. The model is multiple parts, the file contains: 1 x Body 4 x Arms 2 x ½ tongue parts 1 x Intestine 1x Customized 60mm base. ... Support Version Included

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 custom_back_extra_port_y_position = 30 custom_top_port_corner_resolution = 8...

I built the flat surface of the skirt with ParametricPlot3D, then intersected it with a lattice-like model, then I utilized those tables to make two ParametricPlot3D tubular surfaces, which I then pieced together using the Show command to make the...

More information: The models were printed in PetG and have a consumption between 5.7g and 7.0g and the printing times range from 0:47 to 1:15 hour. Note1: If the z selection alignment is used, you can generate a line as the one shown in the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

# Anet AM8 motherboard case This case is inspired by a [YZ Case for Prusa made by Carter](https://www.printables.com/pl/model/1910-yz-case). This case is prepared for mount on the Anet AM8 modification frame. It can hold Anet A8 v1.7 motherboard...

A simple to assemble version of the ER11A Z axis probe that screws onto an ER11A spindle. It has indicator LEDs and can be used to measure and compensate for a bed that isn't flat when engraving, for example a PCB or a curved surface. I use it for my...

The pilings for this model are slightly long at the bottom as they were designed for the display demo table where they would be sunk about 5mm into the baseboard substrate to firmly fix them in place – so if you are planning to use them as free...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_mirror = 0 stencil_drawing =...

The pilings for this model are slightly long at the bottom as they were designed for the display demo table where they would be sunk about 5mm into the baseboard substrate to firmly fix them in place – so if you are planning to use them as free...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 40 printer_tolerance = 0.4...

The pilings for this model are slightly long at the bottom as they were designed for the display demo table where they would be sunk about 5mm into the baseboard substrate to firmly fix them in place – so if you are planning to use them as free...

So it was time to change the software for a version with customizable options. version 0.1 detail Version 0.2 is a rebuild of the FreeCAD model in OpenSCAD. While working on it some additional settings beside the number of legs made sense. Now there...

The pilings for this model are slightly long at the bottom as they were designed for the display demo table where they would be sunk about 5mm into the baseboard substrate to firmly fix them in place – so if you are planning to use them as free...

...More importantly, Thingiverse hasn't run their customizer queue since Jul 10, 2020 so until they fix that issue, you will have to install and run OpenSCAD (free software) on your own computer to process the code to create your own customized models.

The model is optimized for the connectors shown on the pictures. Super glue/cyano acrylate/any other transparent fast setting glue which adheres to your filament. Wire (should be thick enough for 700 mA and thin enough to fit into the carrier ...

Note: A Honeywell Type H filter is virtually the same size (though not tested with this model) and 3M offers a filter that claims to be compatible with both the Aer1 and Honeywell Type H. 36x rare-earth magnets, disk shape, 8 mm diameter, 3mm heigh...

Perfect for storing jewelry, electronic parts, cables, Lego models, tools, and other small items, the Pyramid Stacker offers a practical solution for keeping your belongings organized and within reach. By stacking the layers, you can store smaller...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 pattern_element_overlap = 48 custom_top_port_x_position = -10 custom_bottom_outer_edge_chamfer_radius = .6...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 custom_back_extra_port_y_position = 30 custom_top_port_corner_resolution = 8...

The models (keys and legends) are the same dimensions and should center at the exact same spot. It’s really difficult, and you will fail again and again, but the result is worth it (I think). You could also print the keys upright (with supports) and...

The reason for the former changes is the way I modeled the original was a PITA to modify so some things had to get completely redone (and I left out the less important details to save time). The reason the STL's are so large is simple; I upped the...

And get your supports in order first, the models need a relatively precise and flat supported surfaces. <font size="3">The modification uses many parts from the original setup, but the PTFE tube must be cut, making this a non-reversable mod...