mazda 3 phone mount 3d models
1079605 3d models found related to mazda 3 phone mount.thingiverse
Also needed shorter vent prongs for by Mazda 3, the hook on top, left hook on the bottom too. Added braces for legs since one broke during a test fitting. Mod 5 didn't fit vents very well. ... Mod 6 increased the clip/hook and shortened a support...
thingiverse
This a phone holder designed to hang from the passenger side of the center console. ...The current dimension fit an iPhone 12 Pro very well, but the height can be adjusted in the slicer if needed.
thingiverse
My Mazda didn't have a very good way to mount the phone for viewing maps during navigation. This is quick and simple mount to keep your phone from slipping around. ... I've included 3 different iterations of the design to contour to the console cubby...
thingiverse
I copied the genuine mount of the Mazda 3 center mirror because my is broken. I tried it and its morphed in the hot sun, so i recommend to use nylon or such filament. ...
thingiverse
The boot button on my wife's Mazda 3 had broken, and it was a pain trying to fish around inside the boot to try to find the button. ... This part was made to match up with the boot button.
thingiverse
A car dock / phone holder for Nexus 6P with official adopted case (cloth back) for my 2014 Mazda 3 Sport (hatchback) Reuses same 'clip' as thing:1133955, which is attached onto dash with outdoor mounting tape, then this phone holder part just slide...
thingiverse
Phone holder/ mount for in a mazda mx5 nb/nbfl that uses the orginal radiocover for the minideck. Needed: 5x M3x20 countersink screws 5x M3 nuts. ... Lever arms must be screwed thight else the phone might drop out during epic cornering.
myminifactory
This is a phone mount designed for the Mazda cx-30 2021. It give a nice place to set your phone in the gap center console. The phone shown in the photos is an Iphone 13 pro max although it works great for any type of phone. It allows the phone to...
myminifactory
This phone mount is meant to mimic the original mazda miata "eyeball" vent mount. The goal of this project was to create a mount that is minimally invasive to the original design as possible. The mount fits smoothly into the base allowing for removal...
thingiverse
[DennisP](https://www.printables.com/model/229106-magsafe-car-mount-mazda-2) made a mount for Magsafe that fits my needs, but since I do not have a Magsafe phone, I modified his mount to use 17mm ball mount holder instead. I highly recommend to use...
thingiverse
This is a mount for the center console of a 2020-2021 Mazda CX-30. It clips on to a lip inside the compatment and has feet to stabilize the mount. It does require the center console top to be clicked in the slightly open position but still allows it...
thingiverse
I tried to find a front mount for a reverse camera and couldn't find one, so here it is, it's designed to fit a mazda 3 2014 model but will fit others, just slot into the grill. ...model of the camera in the photos, its a generic rear camera.
thingiverse
... on to the dashboard next to the steering wheel. It grips on the air vent on Mazda 3, which is 45mm wide. It uses the original screen holder and joining plate from the Suction mount. The GPS clamp then just slides into the slot on the arm. ...
thingiverse
Check out version 2: https://www.thingiverse.com/thing:3022608 Cell phone mount for the Mazda MX-5 (Miata) 2016-present. Consider shrinking wedges 2-3% for easier fit. *Requires* PopSockets from Amazon (http://a.co/9WpVO6J) Video Demo:...
thingiverse
This is a fold down phone mount for an LG G4 using an otterbox case, designed to fit into the cubby of a mazda 6, but it could be bolted to anything really! ...Video showing how to install coming soon.
thingiverse
mazda 3 body and tires Print Settings Printer Brand: 3D Systems Printer: Cube 3 Rafts: Doesn't Matter Supports: Yes
sketchfab
The Mazda 3 is a compact car manufactured in Japan by Mazda. It was introduced in 2003 as a 2004 model, replacing the Familia/323/Protegé in the C-segment. A performance-oriented version of the Mazda3 was marketed as the Mazdaspeed3 in North America,...
thingiverse
A "remix" of the s7 mount below, increased the mount to fit a larger phone (LG 6062w which is about 75 mm) https://cults3d.com/en/3d-model/tool/version-2-stiff-samsung-galaxy-s7-mount-for-ender-3-pro-v2-printing-bed-smartphone-mount-for-timelapses...
cults3d
This is the ultimate phone holder, I was sick of the mount I had slipping from the air vents so created this. It clips intot he side of the vents on either side of the hazzard button. This design allows access to the button while keeping your phone...
thingiverse
This is the ultimate phone holder, I was sick of the mount I had slipping from the air vents so created this. It clips intot he side of the vents on either side of the hazzard button. This design allows access to the button while keeping your phone...
thingiverse
I designed this mount to attach a phone holder to my Ender 3 Pro. This was to allow the printer to trigger a smartphone to take pictures and create layerlapses. One of my resulting printlapses: https://www.instagram.com/p/B-aFkMIFHhz/ It attaches...
sketchfab
2 PROCESSING 3 READY TO PUBLISH Title Mazda-3 Description EDITPREVIEW 1024 Categories Select up to 2 categories Tags Add tags Suggested tags: range, rover Discoverability Write a good description, add categories and tags to help your model get...
thingiverse
This is a custom-designed phone cradle I made specifically to fit the interior of my 2008 Mazda 3. It is made to fit into the ash tray which sits behind the gear shift lever, since it is pretty much useless. I have tweaked the sizing so it fits...
cults3d
This is a custom-designed phone cradle I made specifically to fit the interior of my 2008 Mazda 3. It is made to fit into the ash tray which sits behind the gear shift lever, since it is pretty much useless. I have tweaked the sizing so it fits nice...