mbp stand 3d models
153142 3d models found related to mbp stand.thingiverse
The mac_stand_v3_not_so_tight version is with an opening whose upper opening and lower opening dimensions are always 18mm, and the mbp can be put into and pull out easily. ...Print Settings Rafts: Doesn't Matter ...
thingiverse
I was looking for a vertical stand for my MBP, but they were all very large and wouldn't print on the MOD-t. SO I made one. There are no logos, nothing fancy. Just a functional stand. ... I plan to print this after I upload it and add some felt, or...
thingiverse
Remix of - The geometric stand for MacBook Pro Retina - it's just a little flatter
thingiverse
Very simple Macbook Pro 2020 (13-inch) stand. ...No supports needed.
thingiverse
Customized version of http://www.thingiverse.com/thing:1003447 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1003447 Instructions Using the following options:...
thingiverse
This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/3Y3mxVtbVzg
thingiverse
Customized version of https://www.thingiverse.com/thing:1003447 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1003447
thingiverse
Simple notebook holder that can keep my MBP 13" off the table desk. Position is stable and even if it decline from table holder can keep it stable. It is wide enough to keep two notebooks. Printing (ABS) with standard infill (20%) was not...
thingiverse
Just another MBP Privacy shield for the webcam on a MBP 2012 model (non-retina). Not that I do think that some folks will turn on my webcam to watch my boring life, but why take the chance. Printed it at .2 mm and 5% infill, took a little over 40...
thingiverse
Customized version of https://www.thingiverse.com/thing:117519 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=117519
thingiverse
I wanted to print the MBP Stand, but it wouldnt fit on my MP Select mini, so i chopped it! ...You can probably use super glue to get the two halves together.
thingiverse
So you want to hang your BabyCamera on the wall without drilling holes? ... This hook is specificly for the Motorola MBP-48 camera. Take some (good) double sided tape and you can attach it to the wall. ... happy printing!
thingiverse
I changed the dimensions a bit to make it taller and fit my specific charger (2018 15" MBP) a bit more precisely. ...I also cut off the top to make all sides the same height and avoid a razor's edge on the backside of the original mount.
thingiverse
... started over from scratch. Sadly mine ain't quite as pretty as the original. I did add a slot for the cylindrical magsafe charger. I want to store and charge my MBP on the wall without having to fish out a charger cable and plug it in manually.
thingiverse
Remix of "Simple arch MBP stand by zhaosong414" to allow 2 laptops to be stationed next to each other. I also added some extra base to make it a bit more stable. ... I printed in PLA, 20% infill, no supports (if you can handle the bridging).
thingiverse
Customized version of https://www.thingiverse.com/thing:2954310 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2954310
cults3d
This is for the storage of the small miniatures (26mm) of Mythic Battles Pantheon Edit : new one for the "giant bases" Edit2 : "giant bases x2" and "60mm bases x6"
thingiverse
Back clip to hold in place the stat clip of the stat board for Mythic Battles Pantheon. Thin enough, the board still lays flat. ... Easy to mount and unmount.
thingiverse
This is for the storage of the small miniatures (26mm) of Mythic Battles Pantheon Edit : new one for the "giant bases" Edit2 : "giant bases x2" and "60mm bases x6"
thingiverse
just wanted something to hold my phone on my computer. ...Designed in like 5 minutes very custom for my phone and computer may not work for everyone. phone: iPhone Xs computer: 16 inch MBP printed in PLA top side down.
thingiverse
... you might need to adjust slightly to yours or just make this in tinkercad like I did, pretty simple. the height from desk to the bottom recess is 7 mm exact(how high the usb c port is). Also that gray is matching the mbp color almost perfectly!
thingiverse
After printing all you need is the following: 4 x O-ring for M3 2 x M3 x 20 hex screws 2 x M3 lock nuts that are inserted in the MBP Stand part Print Settings Printer Brand: Ultimaker Printer: Ultimaker 2 Rafts: No Supports: No Resolution: 0.2...
thingiverse
Customized version of https://www.thingiverse.com/thing:739573 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=739573
thingiverse
TPU is a great material. ...Strong, flexible and provides good friction. I love this TPU rubber shoe on my MBP.
thingiverse
Laptopholder that can be installed under shelf / desk or on wall. Designed for Macbook Pro or similar (16 mm, gap on design is about 20 mm wide). Design includes versions with larger holes on side for TB3-cables. There is versions with lip onto...
thingiverse
Brackets for mounting a magic keyboard and trackpad underneath a desk. ...This is designed for use with a Twelve South case that holds the trackpad and keyboard together; the case then slides into the bracket underneath the desk.
thingiverse
Clips to keep Let's Split keyboard from moving around while on your laptop (only tested with 2016 Mackbook Pro).