mcpx bl frame 3d models

skid + battery holder for Blade Helicopter MCPX BL. it will be necessary to add 2 screws for the frame fixing. ... the file contains the openwork skate well

This is an mCPx BL battery holder. It holds up to 7 batteries. It is my first design and was made in Sketchup. ... Printed with 5% infill

simple landing gear replacement for the blade mcpx brushless (brushed uses a different battery shape). Print with nylon for best results Instructions parts press together, glue if you want. ... may be...

Heck motor mount for Blade MCPX BL. Incl. FreeCAD file for easy editing. Have fun. ...;)

Battery Holder for a smal "Blade MCPX BL" RC helicopter. ... The white holder is the original holder, the orange the newly printed Battery size maximum 17.2x11.7mm

Tail motor holder for the MCPX BL. The motor diameter is 8.1 mm, the lenght is 20 mm. The hole for the boom is 3 mm (common replacement for the original 2.5 mm carbon tube). ...For original diameter change the variable d_boom in 'mcpx tail motor...

Battery Holder for a smal "Blade MCPX BL" RC helicopter. The white holder is the original holder, the orange the newly printed Battery size maximum 17.2x11.7mm Print Settings Printer: A6 Evolution Cube Rafts: Doesn't MatterSupports: Yes Resolution:...

No need to purchase new skids if you can print.

This project was the result of a long search and evaluation of tool/s capable of "accurately" modeling a complex, curved hard-surface with good surface reflections and continuity. ...

... This is a frame inspired by Kabab fpv's toothpick frame. It use the same parts from Mobula7, powered by 0802 16000KV motor. The prop use 56mm ladybug prop instead 65mm, make the wheel base only 97mm, and do not need to extend the 0802 motor wire.

... and print them with 100% infill to ensure stength and flexibility. You need two carbon rods D=2mm, L=70mm and two small screws fitting into the mcpX body to complete this thing. ... Print, mount, have fun and hopefully don´t crash again :-)

This is a simple tailboom mount, to be used for your Blade MCPx - in case you have pimped it and require something to hold the stabilizers. ...I have made it for a 3mm tail boom, but can be easily adapted to 2mm.

This MCPX BL2 landing gear is a direct replacement for the original landing gear which is very fragile. You need to trim and reuse the old battery tray. ...The landing gear is angled so the tail boom is free from landing obstacles.

... STL and blend file(for further mods) so it'll fit to the frame. Haven't tested it though because my original camera broke from crashes. Main reason I redesign the frame from the original design was to protect the camera(VTX aren't cheap). ...

Main Rotor Blade for the MCPX RC Helicopter. Model is not oriented ideally for printing, Will need to rotate 90 along the blade axis. Supports will be needed. I've printed this out a couple of times, and was pretty please with the outcome. ...

BL

made with sketchup

Customized version of https://www.thingiverse.com/thing:251944 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=251944

A simple tool for helping get your Blade MCPX helicopter's swash plate level. Without leveling your swash, calibration is incredibly difficult. Instructions Print the STL. Most settings work fine. ...If...

... metal fan shroud is about 90 gram, which is sensible for inertia. ... Also not much decent options to mount a BL touch close to nozzle. Thus, I made this minimal frame with BL touch mount included. ... PETG/PC carbon fiber will be just perfect.

Customized version of https://www.thingiverse.com/thing:1341482 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1341482

... rigid and cooler :-) Have fun !! Instructions Cut 2pc., each 70mm long, of D=2mm carbon rods as skids Print front and rear landing gear with high percentage of infill Screw the landing gears onto the mcpx with 2 small screws... ... Have fun :-)

Here is just another part for the famouse Blade mcpX. Rotor Head Central Piece Print with 100% infill at least at 0.1 layer or even smaller... DISCLAIMER: Use at your OWN RISK!!! ...Rotating parts are DANGEROUSE when desintegrating !!!

2.) Dismount the main board and cut away the original mounting struds as close to the frame as possible. 3.) Fit the replacement to the main board mounting struds and also to the canopy rubber spacers (you might have to sand the ends a bit). 4.)...

This is the strong version of the propguard for 87mm Armattan Pershing 87mm frame Fits with 47mm DYS (2030) props Fits with BR1103 racerstar brushless motors

Customized version of https://www.thingiverse.com/thing:739573 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=739573

Customized version of http://www.thingiverse.com/thing:393590 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=393590

No description provided.

Customized version of https://www.thingiverse.com/thing:2482372 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2482372

Customized version of https://www.thingiverse.com/thing:739573 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=739573