meade equatorial mount 3d models
341970 3d models found related to meade equatorial mount.thingiverse
I wanted to use a green laser to help me rough align my Meade Equatorial Wedge. So, I created a jig that slips in the hole and holds my laser pointer. Instructions Designed the model in SolidWorks...
grabcad
A telescope mount with Nema motors attached and a suitable gear set of gear ratio 3*3*120.
thingiverse
Remix of Simon's equatorial mount, to adapt it to a tripod with 3/8" threaded shaft.
grabcad
Work in progress. ...Trying to digitize the cheap equatorial mount that came with my Orion Starblast II 4.5". ...Measurements made with a MasterCraft caliper.
thingiverse
UPDATED: 24 JUN 2022 Updated assemble instruction for 3D printed parts ↓↓↓↓↓↓↓↓ https://mr-deep-addicted.com/?page_id=1300 Full 3D Printed Equatorial Mount. RA: 1:180 DEC: 1:45 With Microsteps 1/16 RA: 1:6400 DEC: 1:400 The heart of this equatorial...
thingiverse
Equatorial telescope mount / adaptor Work-in-progress as I have yet to finish the controller board, code and test the mechanisms. Uses 4 Slew bearings of the thing below, and lots of M3 bolts. ... https://www.thingiverse.com/thing:4979666 OnShape...
thingiverse
These are simple stepper motor brackets for equatorial telescope mounts. My telescope mount is unbranded and inexpensive. I do not know if the brackets will fit other types. The brackets are for Nema 17 type stepper motors. The equatorial drive...
thingiverse
This is my traveling tracking equatorial mount for astrophotograpy. Its turret rotates 360 degress / 23 hours, 56 minutes (sidereal day). The ball bearing groove should be filled with metal 4.5mm bb-gun balls and then locked in with the small plug.
thingiverse
Check out his instructables for more details on how to assemble https://www.instructables.com/id/Equatorial-Mount-for-DSLR/ Changes: -Changed motor to nema 17 -Added another reduction (4:1) -Changed to chevron gears -Replaced all screws with M3 (was...
prusaprinters
DEC_Housing_Back1_PCBSupportUPDATED: 24 JUN 2022Updated assemble instruction for 3D printed parts↓↓↓↓↓↓↓↓https://mr-deep-addicted.com/?page_id=1300Full 3D Printed Equatorial Mount.RA: 1:180 DEC: 1:45With Microsteps 1/16 RA: 1:1600 DEC:...
grabcad
A-Z mount + wedge = EQ mount ... right ? ... Far from finish , needs a lot of work ...
thingiverse
2 units are required for use as a dual-axis (RA & DEC) equatorial mount. BOM for 1 Unit 1 x 6812ZZ Bearing-60x78x10 1 x 6807ZZ Bearing-35x47x7 6 x 606ZZ Bearing-6x17x6 1 x 17hs4401s-pg5.18: 1 (Geared Steppermotor) 1 x Aviation Plug GX12...
thingiverse
If you have trouble finding the clutch handles on your EQ6 mount, in the dark, you can try replacing the original black metal ones with glow in the dark ABS ones. I even replaced the ones on the tripod legs, which are identical, to make it easier to...
thingiverse
An adapter to mount the standard Meade spotting scope on the side of the Meade ETX125 scope body rather than using the standard mount point that tends to get in the way.
grabcad
Hello guys, this is my project from my studies in France. ...I deal only with the axis of the right ascensions of the telescope that is designed to be used in Alsace.
thingiverse
All of my projects were printed with a Prusa Mk3S. - 12V battery - 1 arduino - 1 cnc shield or electronics to run a stepper motor - 2 buttons - 1 screen - 1 on-off switch - 1 lead weight - 1 Flange Other than 3D Printed parts: - 1...
thingiverse
I made a simple stepper motor (nema17) support to motorize an equatorial mount. The brand of the mount is Mizar. ... The telescope is 114/900 Mizar.
cults3d
all of the details are on instructables here : https://www.instructables.com/id/Equatorial-Mount-for-DSLR/ or on my Instructable account
thingiverse
all of the details are on instructables here : https://www.instructables.com/id/Equatorial-Mount-for-DSLR/ or on my Instructable account
thingiverse
... (10.5mm) is needed. As well as two M6 wing screws and washers (optional) to fasten plate to mount. Bracket and spacer are replacements for original part of SkyWatcher 130M EQ2 Equatorial Mount. ... My first attempt to design parts from scratch
thingiverse
I use Arca Swiss Mounting System and changed the Base for the Equatorial-Mount. Arca Swiss is very common, so i thing others will use this too. I live in the area of cologne, this is why i chnaged the angle to 51° ( The angle of the north star is...
thingiverse
This is an interface to mount a Nikon DSLR on an equatorial mount (the celestron CG-2). The part is introduced directly in the mount dovetail. Needed : Screw M4 x 16 mm Nut M4 Screw 1/4" (photo) Printed in PETG for the thermal resistance. ... ...
thingiverse
A larger version of my static wedge to allow a Celestron Nexstar Mount to track in equatorial mode. This one fits mounts such as the Nexstar 114 GT, with a upper cone diameter of 125mm (the original one fits 100mm, and can be found here:...
thingiverse
I do not know the brand and model of my equatorial mount, but you might be able to remix these brackets and gears to fit your particular mount. ... Dave Ek's Digital Setting Circles: https://eksfiles.net/digital-setting-circles/ DSC ASCOM driver:...
thingiverse
A Static wedge to allow a Celestron Nexstar Mount to track in equatorial mode.This one fits mounts such as the Nexstar 80 GTL, with an upper cone diameter of 100mm (for an upper cone of 125mm, see https://www.thingiverse.com/thing:4879004). I've...
thingiverse
This kit aids in initial polar alignment of your equatorial mount. The included plummet (plumb bob) is attached to the mounts counter weight shaft and a second plummet to the mount center bolt. These will settle on points on the ground that should be...
thingiverse
This design is based on SimonRob's Equatorial Mount for DSLRs (https://www.thingiverse.com/thing:4365068), but it's been upgraded to handle smooth tracking on a lightweight telescope setup. A huge thanks to him for laying the groundwork, and I...
thingiverse
The center hole diameter is 19mm, which is suitable for Takahashi EM-11 equatorial mount. Printing in PLA is recommended. 25% infill is good enough for most case while 10-20% infill can save much material and time over reasonable body strength. ...
thingiverse
Snap on filter mount for 8x25 finder that comes supplied with many MEADE telescopes, including the ETX series. ... I made this to mount a piece of solar filter from a pair of solar glasses to the finder of my ETX90 prior to shooting an ISS solar transit...