measuring tape fabric 3d models
158869 3d models found related to measuring tape fabric.thingiverse
I made this to hold my fabric (soft) tape measure. I added a thumb inlay for easier spinning after I printed mine. ... The metal end of the tape slides into a slot on the top piece and secures it in place.
prusaprinters
I made this to hold my fabric (soft) tape measure. ...I added a thumb inlay for easier spinning after I printed mine. The metal end of the tape slides into a slot on the top piece and secures it in place. Print Settings Printer: Gmax 1.5+ Rafts: No...
thingiverse
I bought one of those fabric tape measures a while back because they are fantastically useful for measuring oddly shaped things or perimeters. The problem is that they get tangled and bent faster than a neatly coiled pile of usb cables. This device...
thingiverse
Also, the tape measure my wife has has a rivet on the metal end protector that caused it to crack the inner holder. I addressed these problems by making a counter sunk hole for a #10-24x5/8 flathead screw and increasing the size of the center of...
thingiverse
Widened it for a 20mm tape. Changed the cover design. ...Tightened the tolerance between the top and the spool.
thingiverse
Remixed to have smoother edges and reduced size to accomodate an 18mm wide tape. ... Tolerances are tight, but after sliding back and forth a few times it is a good fit
prusaprinters
... ...I originally added a small fillet to strengthen it but this interfered with the slot for the tab on the measure. ...I remixed it to utilise a bolt and a brass insert.</p><p>You will require:</p><p>1 M3x25 Caphead bolt<br>1 M3x5 brass insert</p>
thingiverse
Turn your ordinary fabric measuring tape into a full on tape measure, with this fabric tame measure spooling case! No glue or fasteners needed, it all snaps together! I built this design around a ~120inch/305mm tape with a width of ~20mm. The .scad...
thingiverse
- Centered and symmetrical notch means you can insert the measuring tape from either end. Print the two halves separately and then fit the pegs into the holes to assemble. In my tests with PLA, it was a nice fit and did not require glue, but you...
thingiverse
This makes ZevEisenberg's tape measure holder too big for my purposes. So I redesigned it for a maximum measuring range of 15mm. I also changed the attachment of the cover plate. I use two M3 x 10mm countersunk head screws. I sunk two M3 nuts into...
thingiverse
I originally added a small fillet to strengthen it but this interfered with the slot for the tab on the measure. I remixed it to utilise a bolt and a brass insert. ... You will require: 1 M3x25 Caphead bolt 1 M3x5 brass insert <a...
thingiverse
This is a remix of the measuring tape spooling case by thistof.
thingiverse
Tape holder for a 3 Metre (10') x 20mm(3/4") fabric tape. The spool (knob) was the only item that needs support for printing, although all items were printed with a raft. ...3x 20mm by 3.5mm screws are used to fasten it together.
thingiverse
I uploaded 2 versions with differing tolerances. ... The same concept as the original but made the post stronger and rounded the sharp corners thanks to @chillhaus for uploading the 360 files.
thingiverse
A simple case to hold your fabric tape measure. To put together: 1. Insert the metal end (from the highest number side of the tape) into the center slot. 2. Use a little smear of dish soap or wax on the sphere located on the peg of the lid...
myminifactory
A simple case to hold your fabric tape measure. To put together: Insert the metal end (from the highest number side of the tape) into the center slot.Use a little smear of dish soap or wax on the sphere located on the peg of the lid component.Thread...
thingiverse
-------------------------------------------------------- I took direct inspiration from Fabric Tape Measure Holder (Rounded) by ZevEisenberg I wasn't a fan of the dual rods on the design and completely omitted them with this design. You will need a...
thingiverse
This is simply the clip file scaled up to fit a 120 inch tape. ...It works with the original base.
thingiverse
Customized version of https://www.thingiverse.com/thing:1680831 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1680831
thingiverse
Customized version of https://www.thingiverse.com/thing:1680831 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1680831
thingiverse
Customized version of https://www.thingiverse.com/thing:1680831 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1680831
thingiverse
Customized version of https://www.thingiverse.com/thing:1680831 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1680831
thingiverse
Customized version of https://www.thingiverse.com/thing:1680831 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1680831
thingiverse
Customized version of https://www.thingiverse.com/thing:1680831 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1680831