mega tree topper 3d models
79140 3d models found related to mega tree topper.cults3d
I designed this topper for an 16 string 180 degree mega tree. I used sainsmart TPU with solid infill and it works great. I made it so that a 1/4 inch threaded rod( along with 2 washers and 2 lock nuts) could be inserted through the hole in the back...
thingiverse
I designed this topper for an 16 string 180 degree mega tree. I used sainsmart TPU with solid infill and it works great. I made it so that a 1/4 inch threaded rod( along with 2 washers and 2 lock nuts) could be inserted through the hole in the back...
thingiverse
This is a tree topper I designed for my Mega Tree. It is 6" which is much smaller than most you can find on the market which is what I wanted because I wanted my tree to come to a point at the top (or look as close to it as possible). I designed...
prusaprinters
I designed this topper for an 16 string 180 degree mega tree. I used sainsmart TPU with solid infill and it works great. I made it so that a 1/4 inch threaded rod( along with 2 washers and 2 lock nuts) could be inserted through the hole in the back...
cults3d
Had bought four of these for my show and decided to build two small trees to go beside my Mega tree. The topper was designed after several attempts. It uses ¼ x 1-inch bolts that screw into the topper at an angle and hold the strings. Center pole...
thingiverse
As the holiday rolls around, welcome guests with a 3D Printed tree topper (Star)
thingiverse
I created a tree topper for our Christmas tree. Maybe you’ll need one for your Christmas tree too. To assamble the tree topper you have to glue the two parts together. ...It fits on branches with a diameter of 12 mm or less.
thingiverse
Its getting close to Christmas so I decided to design a tree topper. ...It will take about two and a half hours to print with recommended settings.
myminifactory
... 10mm LEDs. (Some assembly required). I use Loctite Plastics Bonding System to attach the PETg parts, different filaments could use different adhesives. Prints with no support and no infill. It is a dodecahedron - 1 side to be a tree topper.
thingiverse
Tree Topper holds most models with a 60mm round base. It's shown holding Dutchmogul's amazing Njordsdottir and Undead Treeman. Putting a little LED light in it makes a huge difference! It could also be used as a nightlight lamp too. Thanks for...
thingiverse
... of eternal life. This tree-topper version shouldn't require any support material to make, but includes slots for "twisties" to tie the cross to a top branch. ... I printed it on my Bukobot V2 duo diagonally so a 10" long part like this would fit.
thingiverse
A beautiful laser engraved plywood Policeman to adorn the top of your christmas tree. ...More at http://mememakerusa.com
pinshape
SummaryTree Topper holds most models with a 60mm round base. It's shown holding Dutchmogul's amazing Njordsdottir and Undead Treeman. Putting a little LED light in it makes a huge difference! It could also be used as a nightlight lamp too. Thanks for...
cults3d
I shoved some LED lights from the string on my tree inside and voila! In order to get the support needed to print this I have some struts added, the things that look like wings. After printing just snap them off (I used a pair of pliers, and...
thingiverse
I shoved some LED lights from the string on my tree inside and voila! In order to get the support needed to print this I have some struts added, the things that look like wings. After printing just snap them off (I used a pair of pliers, and...
thingiverse
This was printed and used on: TOM # 4890 MK6+ 1.75mm .4 nozzle ABP with aluminum plate topper and titanium belt covered in kapton Instructions Print Remove top right M3 stepper bolt from extruder Slide the Mega Felt Marker Topper over your 1.75MM...
cults3d
... probably guess this was only tested on a factory MK6 setup and I have no idea if previous extruder builds will work. This was printed and used on: TOM # 4890 MK6+ 1.75mm .4 nozzle ABP with aluminum plate topper and titanium belt covered in kapton