meltink 3d models

So I bought some beautiful blue PLA from Meltink on Amazon. Sadly, their spool didn't have even holes on both sides, so it wouldn't hang properly on our Prusa 3D. This fixed it! Print Settings Printer: Original Prusa i3 ...

This is a set of filament spool hubs for MeltInk brand spools. Their spools are kind of weird in that they have a large opening on one side and a small opening on the other. ... Just print one of each size plus the center rod and you're good to go.

This is a set of filament spool hubs for MeltInk brand spools. Their spools are kind of weird in that they have a large opening on one side and a small opening on the other. ...Just print one of each size plus the center rod and you're good to go.</p> ...

Customized version of http://www.thingiverse.com/thing:36112 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=36112 Instructions Using the following options:...

Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069

hotend: 200 ºC bedtemp: 50ºC speed: 25mm/s enable retraction infill speed: 35mm/s travel speed: 45mm/s Filament From meltInk. ...Thanks, guys.

It's not the best machine and probably worth replacing... ...but it's part of my wife's routine in the morning.  Crisis averted! JGAURORA, MeltInk PLA/PHA Black

Print Settings Printer: Zortrax M200 Rafts: Yes Supports: Yes Resolution: 290 microns Infill: Light Notes: Printed with MeltInk gold PLA using the Z-Temp temperature control accessory for 205ºC extrusion temperature. ...No bed heat, dual fans at 100%.

Print Settings Printer: Zortrax M200 Rafts: Yes Supports: Yes Resolution: 290 microns Infill: Light Notes: Printed with MeltInk gold PLA using the Z-Temp temperature control accessory for 205ºC extrusion temperature. ...No bed heat, dual fans at 100%.

... stick on mount. ...The mount will fit perfectly in the recess. I also changed the square holes to fit and the clearance holes for the bolts. The photo is with the bike handle grips installed. Print Settings Resolution: .2 Notes: Used meltink PLA/PHA

... Summary Thingaverse fit the bill. ...Thingaverse fit the bill. . This was printed in MeltInk Clear PLA filament. Print as oriented. ...I have also attached the 123d Design file for ease of customization.

I used my Ultimaker 3 to make these dual colored ornaments with my cousins names on them. ...I used 50% infill at .2mm. The green filament is actually from MeltInk and the silver is from Ultimaker. ...I used Solidworks to add the text.

... to be collapsed and stored flat. All parts are made to be printed flat without supports. Materials used: Tree,post and spacer: Meltink Dark Green PLA Base: Hatchbox Wood PLA Star: Hatchbox Gold PLA Bulbs: ANY Colored Clear or Translucent PLA

... glowing mushroom lamp. ...The stems were made with a 3D pen. I also included the files for the base of my light, although it was made especially for my piece of wood... might be useful just to take a look at though! Printed with MeltInk Aqua Glow PLA

It was designed using a MeltInk spool but may fit others. I will add other designs as I modify it to fit other spools. Print Settings Printer: Hictop Rafts: No Supports: No ...

... to cosplay characters from Star Trek Voyager, here is an easy starting point for your costume. Badge was modelled in SolidWorks and test printed on a FlashForge Creator Pro and Lulzbot Mini Printer. Seen here printed using MeltInk Silver filament

... Resolution: .2 Notes: Pieces glued together with CA. Used PLA/PHA by Meltink. ...225 and 65 bed.

... is nearly no friction and your spool with move freely. The hole in the center of the bushings measures 1/2".  The bushing anything securely between 2.75" and 2.25" deep as engineered.  Proven on: HATCHBOX, JUSTPLA, PUSHPLASTIC, AND MELTINK SPOOLS

This was printed in MeltInk Clear PLA filament. Print as oriented. I've also attached the 123d Design file for ease of customization. ...Print Settings Printer Brand: LulzBot ...

Print Settings Printer Brand: Printrbot Printer: Simple White Rafts: No Supports: No Resolution: .2 layer height, .4mm nozzle Infill: 100% Notes: Recommend 205 degrees for MeltInk. Brim worked best, just pull out the support inside the hat with a...

Here are the settings I used: Inland's red PLA: Temperature: 220 C Bed temperature: 57 C MeltInk's gold PHA: Temperature: 245 C Bed temperature: 60 C ***Every 3D printer is different (and also material), so printing this out the first time may not...

for all the other parts you need to go to Jarlang's model. Print instructionsCategory: Vehicles Print Settings Printer Brand: Printrbot Printer: Play Rafts: Yes Supports: Yes Resolution: 0.3mm tip with 0.05 layers Infill: 20% Notes: Sliced with...

Settings I used in Slic3r: Layer height: .2mm Solid layers: 3 Infill: 20% With a 5mm brim Temperature: 215 for extruder and 50 for headed bed (with glass) Printed using Meltink PLA. I used TinkerCad to design this thing. If you'd like to customize...

... the size. Print Settings Printer Brand: LulzBot Printer: TAZ 6 Rafts: No Supports: No Resolution: .30 Infill: 100% Notes: Printed in MeltInk PLA without support. ... For best results print place the largest area of the part (tops) laying on Table.

Meltink Cool White PLA/PHA is used with an extruder temperature of 220C and the heated bed at 60C for the FDM models. The extruder temperature is close to the limit for that material (230C) to exacerbate the need for cooling. ... The results are...

 We've tested them (MeltInk PLA) on  both rivers and lakes and they work great! To complete the print, there are a few things you should do: Bottom 40mm Clamp should be printed with the logo oriented UP (Z positive) Top 40mm...

The design can be edited on Tinkercad at https://tinkercad.com/things/evclLyuzWxCPrint SettingsRafts: YesSupports: YesResolution: 290 micronsInfill: "Light"Notes: Printed in Meltink's absolutely wonderful PLA+PHA, using a Z-Temp™ to set extrusion...

... I've been looking to organize. Win-win!! Enjoy! Print instructionsCategory: Tool Holders &amp; Boxes Print Settings Printer Brand: Prusa Printer: i3 MK3 Rafts: Doesn't Matter Supports: No Resolution: 0.2mm Infill: 15 Filament: MeltInk PLA/PHA White

( http://www.thingiverse.com/thing:800175 ) Also added in the nostrils Print Settings Printer Brand: LulzBot Printer: TAZ 5 Rafts: No Supports: Yes Resolution: .25 Infill: 30 Notes: You will need grid support everywhere at 0 degrees angle, fill of...

If it has others uses for you, I'd be happy to see them in the comments! Enjoy! Print instructionsCategory: Hobby Print Settings Printer Brand: Prusa Printer: i3 MK3 Rafts: No Supports: No Resolution: Whatever you wish. Infill: 10% Filament: Meltink...