melzi board 3d models
81345 3d models found related to melzi board.thingiverse
it have a reset botton, it is particular usable because the melzi board do not read the micro SD when you change it without reboat the board. the 40mm fan is exactly in the right place so it will cooling every controllers and mosfets for the bed...
thingiverse
... file can be provided upon request. I've seen a few cases for the Melzi board, but they are always snap-on fronts, and the snaps break. ...So here is one with tons of air-flow, access ports on all four sides, and can be secured with screws and nuts.
thingiverse
How many MELZI Boards had to die because one of the stepper driver or power MosFETs went up in smoke? These tiny IC`s are getting real hot in use, even with heatsink and not everyone is capable of soldering SMD. To save me from this, I looked for a...
thingiverse
This is for Melzi printer boards, V1.0, 1.1, 1.2, and 2.0. There was only 1 model for the melzi 2.0 before and it would require me to bend some pins out of the way just to place on. This could be screwed down, but i prefer having it slot over the...
thingiverse
The USB socket on the Melzi Controller Board can get quite a bit of stress. After having to resolder it, I designed this clamp to take some of the strain. The design uses an M3 8mm Cap screw, an M3 20mm cap screw, one M3 washer and two M3 nuts. ...
cults3d
M3 Bolts all round, recomend mounting board to mount then mount to frame but can be done any way you want :) i made this to fit my tronxy p802 melzi board when i converted it to a p3 steel, fits nice, gives access to everything with space underneath...
thingiverse
M3 Bolts all round, recomend mounting board to mount then mount to frame but can be done any way you want :) i made this to fit my tronxy p802 melzi board when i converted it to a p3 steel, fits nice, gives access to everything with space underneath...
myminifactory
This is a Melzi Board holder, to move the board further out to gain Z Hight on the Huxley RepRap.A Melzi Board is a compact all-in-one controller board for RepRaps with one extruder head, optimized for mass production.The point of RepRap is to make...
thingiverse
This Support Free Melzi Board Case should allow you to mount your Melzi anywhere you like using the extended legs. Using these for mounting to a surface, you can remove the case when working without having to remove the board itself. This will...
thingiverse
Here we have some *reportedly* good firmware for the anet a8 using a melzi board. NOTE: I don't own an anet a8 nor would I ever buy one, therefore I have no actual means of testing this firmware, USE AT YOUR OWN RISK! It has been reported...
thingiverse
Modificación del soporte para adaptarla a la placa Melzi del fabricante Tronxy. El soporte original chocaba con un conector de la placa de Tronxy y he tenido que modificarla añadiendo unos pilares para los tornillos. La verdad es que ahora los divers...
thingiverse
This is a cooler for a Melzi board with two 40mm fans. It is designed to leave space for the wires coming from the board. ...
myminifactory
This is a cooler for a Melzi board with two 40mm fans. ...It is designed to leave space for the wires coming from the board.
grabcad
Simple standoff mount for a GT2560 Melzi board.The 2 mounting holes in center are designed for 4mm screws.Standoffs are designed to be tapped with 3mm threads.
grabcad
I am building a Prusa i2 reprap 3D printer and bought a Melzi board for control. I wanted a nice way to mount it that looked like it belonged with the rest of the design. ...So I modeled this up.
thingiverse
Some of the new 3D Printers sold on Aliexpress have a square melzi board instead of the long rectangular ones. I printed with .02 layer, 15% infill and no supports. Might want to increase bottom and top layer a bit for a smooth finish. The cover is...
thingiverse
Simple standoff mount for a GT2560 Melzi board. The 2 mounting holes in the center are designed for 4mm screws. Standoffs are designed to be tapped with 3mm threads. ... The specific board is here :...
thingiverse
... make this after I saw the [Tronxy x3 control PCB cradle](https://www.thingiverse.com/thing:2775139) by [Richard Baldock](https://www.thingiverse.com/baldrick131/about). ... This is a Melzi Board support frame that fits inside the TronXY X1 control box.
thingiverse
Pièces additionnelle : 2 vis nylon M3x8 et 2 écrous nylon M3 UPDATE 07/04/16 : Mise à dispo des pièces en .step These pieces are made for mount the melzi board on the discovery 200. The difference between the original is that it give access to the...
thingiverse
You will also need some spacers (8mm) between the top cover and the Melzi board. I made spacers from cable insulation, nothing fancy. The top cover should sit over terminals and line up with the M3 bolt holes. Next, fit the base cover over the...
thingiverse
Casing which will protect Melzi board on REPRAPPRO Mendel printer easy way to mount wiring to Melzi board fix with 3 couplings to threaded rods (
thingiverse
I made this remote switches for setting the Melzi's with no easy access. ... UPDATE 07/04/16: adding .step files
thingiverse
Melzi cooling bracket (40mm fan) Customized version of http://www.thingiverse.com/thing:166045 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=166045 Instructions...
thingiverse
Reorganized mounts to support Creality Board V2.0 which comes with Stock CR10S. ...Also adapted the slot for the dual cable to the display ...
thingiverse
If you have bought an Aldi Cocoon printer or Wanhao Duplicator and you want to get rid of the original metal box and have access to the reset / stop buttons on the Melzi board (that's right, it has an Melzi board inside), and the reset and light...
thingiverse
#Ender 3 - Fresh Air System I got big heat problems with my "Melzi-Board" inside my "Ikea Lack" enclosure for the Ender 3. It can reach up to 40-50°C inside the enclosure, especially @printing with ABS!! And this is my solution for this problem!...
thingiverse
there are some objects for melzi and prusa, but they where too big to print it on 210x210 bed and they are not mounted like i whanted to have it. on the picture (the protoype) there are 8 nibbles to snap it, but i removed 4 of them, cause its now...
thingiverse
I made this remix for the mosfet with 60.5x26mm (12/24V) hole spacing. ... The Melzi board has a lot of flex so I added a support bar between the mounting holes. ... The Melzi board support is also included standalone.
prusaprinters
Adapter bracket to install a BigTreeTech SKR v1.4 and optional MOSFET in the Wanhao Duplicator I3 using the welded-in mounting bosses intended for the stock Melzi board. Note that the USB and SD ports do not line up with the original holes in the...
thingiverse
Adapter bracket to install a BigTreeTech SKR v1.4 and optional MOSFET in the Wanhao Duplicator I3 using the welded-in mounting bosses intended for the stock Melzi board. Note that the USB and SD ports do not line up with the original holes in the...