metal plus llc 3d models

Foot Bracket for PrintRBot Metal Plus. ...For securing printer to a table.

The Printerbot Metal Plus can be prone to tipping. ... These feet are designed to stabilize it a bit.

My implementation of the Octroprint into the Printrbot Metal Plus. I'm using the Raspberry Pi Model B+ with a 12" Pi Camera Cable. Extension Arms are adjustable, using M3 Screws to set and tighten. The Case is attached to the PrintRBot...

I had an idea for a spool holder that sits on top of my Printrbot Metal Plus. The printer design is such that you can just set a spool up there, and it pretty much works, but I was worried it might fall over or something. I took the 80mm gap at the...

Gemelos LLC

Customized version of https://www.thingiverse.com/thing:739573 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=739573

I had an idea for a spool holder that sits on top of my Printrbot Metal Plus. The printer design is such that you can just set a spool up there, and it pretty much works, but I was worried it might fall over or something. I took the 80mm gap at the...

http://www.thingiverse.com/apps/customizer/run?thing_id=147178 Instructions Using the following options: length = 400 lastrule = CCEPSC, LLC font_key = write/orbitron.dxf image = back_to_school_v2-120150529-13780-5v3ujd-0.dat rule_length = 228.7...

http://www.thingiverse.com/apps/customizer/run?thing_id=46704 Instructions Using the following options: text1_size = 10 add_back = None ring_y = 27 ring_x = -2 cut_hole_in_image = 1 text1_tickness = 3 image = Dodge Logo rectangle_height = 60...

http://www.thingiverse.com/apps/customizer/run?thing_id=40705 Instructions Using the following options: message_two = Trust, loyalty & Integrity hole_radius = 2.5 icon = 3 manual_length = 100 font_one_size = 23 Font = write/BlackRose.dxf sign_size =...

These are the printable files for the two shrouds for the Printrbot Metal Plus

I modify the inital glass clip by bitrunner to make this usefull on the printrbot metal plus :-)

I modify the inital glass clip by bitrunner to make this usefull on the printrbot metal plus :-)

A modified version of https://www.youmagine.com/designs/spool-coaster-for-printrbot-metal-plus No longer requires any screws just 4x cheap 608 bearings.

... and provide airflow to the extruder from every direction rather than just the back side. ... This part attaches with the existing harware and replaces the stock fan shroud on the Printrbot Metal Plus. ... I printed the part out of PETG at 100% infill.

I loved the Simple Metal Footprint by Thorped (Thing 593072) that I printed for my Simple Metal, so decided to design one for the Metal Plus keeping the aesthetics similar to Thorped's original design. I found the Metal Plus to be a bit unstable...

I loved the Simple Metal Footprint by Thorped (Thing 593072) that I printed for my Simple Metal, so decided to design one for the Metal Plus keeping the aesthetics similar to Thorped's original design. I found the Metal Plus to be a bit unstable when...

Just a simple guide that snaps onto the top of a metal plus to keep the filament from kinking inside the machine. ... (The fit on my printer was fairly tight, you may have to sand the clips a bit to get them to snap down)

While printing huge prints with my Printrbot Metal Plus, i had one or two big prints messed up by heat bed cables being caught under GT2 Belt. To avoid this i build this cable cache. ...Look at the pictures to place it.

This is a remix of a remix, The original was from SpannerHands over on Thingiverse. Basically it's a pair of feet for your Printrbot Metal Plus with one of them having an LED 12v 30A PSU build in. It allows for the wires to pass through to the...

My mod of dubi's PrintrBot Metal NinjaFlex adapter (http://www.thingiverse.com/thing:439617) to work with a Printrbot Metal Plus. Use a razor blade to thin the curvature that fits under the tooth gear if needed. Provided non cut hole version for...

A GoPro mount for the Printrbot Metal Plus. It hinges onto the top frame and hangs down, set your gopro to upside down mode and your set! It sits an angle that is perfect for recording. Print Settings Printer Brand: Printrbot Printer: Printrbot Plus...

Very simple guide that slips into the top panel of the metal plus. 4mm hole will accommodate most common sizes. The guide with slides back and forth some with the movement of the carriage but it stays securely locked into the panel. ...

metal C128D Floppy Lock Plus Replacement for broken floppy lock on a Commodore C128D (metal version) retro-computer. Plus stands for the added material surrounding the "half-moon" plug, compaired to the original floppy lock. The floppy-drive drive...

This is a shroud to go over the Printrbot Metal Plus' Y-axis pulleys, helpful if you have a heated bed and have any concerns about the wires getting caught in the belts. Please note the stl is slightly different from the photo. In my original...

Spool bracket for Printrbot Metal Plus. Hole is sized to fit 3/4" PVC pipe. It mounts onto 2 of the 4 Z axis screws at the top of the frame. This makes it very solid and doesn't affect the Z-axis guide. It is way over-engineered. Use 2-3 walls...

Minimalistic spool holder for the metal plus. Add as many of the "middle" brackets as you like for support for longer rods and more spools. A printable 17cm long rod is included, alternatively you could probably use a 7.5 or 8mm metal rod. (I haven't...

... wires through the chain. You'll need to print at least 14 pairs plus the motor mount.Black zipties can hold the chain in place, using the same holes that are used for the braided wrap zipties. ... To install the motor bracket, remove the motor.

Logo made for the Carolina Grace LLC company

I put it like that because Madryn 3D-CNC LLC https://www.thingiverse.com/Madyn3D-CNC_LLC/ is so stupid that it reminds me of Homer Simpsons Le puse asi por que Madyn3D-CNC_LLC https://www.thingiverse.com/Madyn3D-CNC_LLC/ es tan estupido que me hace...