miata cup holder 3d models

This is an insert into the box cup holder of my 1999 Miata so it can actually hold a cup about the size of a regular soda can.

a single cup holder for Miata 89-05 diameter is at 72mm you may try to print it to a more heat resistant filament (ABS??). I printed it in PLA, it may deform due to heat. ... you may need to sand down the "hook" part.

Lost one of my cup holder lids on my NA miata, so I modeled up a new one! Fits perfect, looks great. Modeled was saved in mm, so no scaling should be needed. Best if printed with logo facing up using supports. ...I may emboss the logo so it can be...

This is a remix from https://www.thingiverse.com/thing:398515 Dual size cup holder for na miata intented to hold cans, bottles, and Lg/Med/Small cups. I included an indent in the bracket for the screw to sit in. I used tinkercad, so it's not the...

remixed this to allow for the Pure Leaf bottles to fit Added a taller one that is the same as the OEM cup holder thickness

Cup holder for NA (first generation, '90-'97) Mazda MX-5 Miata. Takes the place of the original ash tray. Print one body, two clips. Clips glue easily into place. Tray is optional - it simply fills the area under the cup holder to protect against...

A Cup holder for Fiat/Abarth 124 spider and MX5 (Miata) The original file has been cut into 2 parts for printing simplify, the 2 parts must be glued

The cup holder on my NB Miata sucks as an actual cup holder. I made this insert to address it's great, square shortcomings. Designed to fit a Starbucks Venti cup. ...Other beverage containers may fit but I make no promises.

The cup holder on my NB Miata sucks as an actual cup holder. I made this insert to address it's great, square shortcomings. Designed to fit a Starbucks Venti cup. ...Other beverage containers may fit but I make no promises.

This im my design of a cup holder for a Mazda Mx5 NA. I once saw a similar design in a Youtube video but the guy didn't make his design public. So I made my own. It comes with custom support beam on the part that is screwed in. It is mounted on the...

I just needed a bigger cup holder for my Miata, the one by Mirko looked pretty good but it didn't fit my water bottle so I enlarged it a bit. It is now about a 76mm inner diameter. ... The onshape file is attached:...

You know that the Cup Holder Placement Sucks. So I have taken the part and removed the top, and designed this part to take its place. The Upper Shelf holds just about any cell phone flat, and the cut thru allows for the use of the pocket. Loose...

Solving an issue with under sized cans tipping over in cup holders.

The connector piece was designed to be the same dimension as 5te3l0k's cup holder design. I simply added a fillet to the connector (to alleviate the stress in that area), changed the cut patterns, and increased the inner diameter. As noted by...

The updated version of my cup/phone holder for an iPhone 12/13 with a case

i created this to hold my iPhone 6 with a life proof steady in the cup holder area it took a lot of tweaking to get it right but it works perfectly and is a snug fit on the phone but also leaves access to all the buttons and ports! i included the...

and if you print don't forget to post it on here i wanna see some miatas and their fancy new cup holder! Please note this will only fit an iphone 6 with a lifeproof case if anyone wants it just for the 6 request it and i will see what i can do :)...

This is a cup holder made for NA & NB Miatas. I drink a lot of 16oz cans, which tend to spill everywhere inside the center console of my NB1. The cup holder is designed specifically for cans but you could fit some cups and bottles in too, or adapt...

This is a new faceplate for the ahstray in older model miatas (NA models) to convert the ashtray to a cup holder. It is very secure because it uses the factory interface and it is swappable in case someone buys the car and prefers the factory parts.

ND Miata MX-5 Cup Holder Phone Mount by BEAVIS

... did not put a supporting structure inside the cover. This requires the use of an NB1 cup holder arm. In the NB1 arm rest, there is an arm that flips over to give you a second cup holder. ...Remove this from the arm rest and use it in this cover!

2 Pieces, should be easier to print. ...Made to resemble the original Mazda part.

The centred arc cut-outs of each square side hold a can or cup and the nipples prevent a mobile phone, diary or other rectangular item from sliding around when placed flat. ... The tray has been resized to better sit in the bottom of the recess and...

This is a standard phone-holder for the miata, I didn't use the cup-holder at all and this was the best place for my phone to sit without having my view disrupted or something mounted to the dash. It is made for the oneplus 7t pro with a slim case,...

This is a low profile passenger side cup holder, specifically designed for the Starbucks Grande reusable cup. ...Hoop inside diameter is approximately 75 mm.

This is a low profile passenger side cup holder, specifically designed for the Starbucks Grande reusable cup. ...Hoop inside diameter is approximately 75 mm.

Is your Mazda MX-5 ND cup holder too small? Well here's a cupholder extension to allow you to fit your larger drinks like Gatorade / Powerade and Bubble teas. ... Credit to blazer34i for the Miata logo :)

Remix of [this cup holder](https://www.thingiverse.com/thing:1667376) and this Miata phone holder from GrabCad: https://grabcad.com/library/na-mazda-miata-cup-holder-cell-phone-mod-1 I don't have the OEM ashtray that the GrabCad phone holder was made...

This is a adapter to hold an 8oz red bull can in an NA miata cup holder. Do not print this in PLA and leave it in your car, because it will shrink. ABS or PETG should work in a hot car. I printed this top side up, which used alot of support for...

Hopefully this will help someone out. ...I broke mine and didn't see one on here already. This is for my NA Miata but I'm sure it could work with NB as well. I printed this so the backside is on the bed. ...That way the part you see is much cleaner.