micro roni charging handle 3d models

RONI HANDLE CHARGING - CAA G1

FR: Socket recuperator for Micro-Roni Gen3, to be mounted on the right front rail, requires two M4 screws (for fixing on the rail and as a pivot). It opens to the side and locks onto the stock lock (foldable). The door has holes for gas...

J'ai pu faire un essai concluant de l'arme : https://www.youtube.com/watch?v=IjROuzy_csQ Here is a part that allows you to use a Glock 44 (22lr) in a Micro Roni Gen 4 stock. It is necessary to disassemble the Roni stock to insert this part. ...

Thumb rest for Micro Roni, just print and snap

Thumb rest for Micro Roni, just print and snap

Simple wall mount for the Micro Roni Gen4 I used 4.5 x 40 mm screws to fix it on the wall. Print instructions4 walls, no supports, 10% infill.

This is a RONI style attachment that can be attached to any Airsoft pistol and converts it to a cool futuristic machine pistol lookalike as long as there is a P-Rail attachment on the pistol. Tomorrow I will publish the Mini RONI carbine version has...

This is a RONI style attachment that can be attached to any Airsoft pistol and converts it to a cool futuristic machine pistol lookalike as long as there is a P-Rail attachment on the pistol. Tomorrow I will publish the Mini RONI carbine version has...

http://www.thingiverse.com/apps/customizer/run?thing_id=749887 Instructions Using the following options: textsize = 25 do_shift_font = automatic RoundedBase = 0 baseheight_percent = .33 shift_font_percent = 0.07 textstring = RONI textheight = 10...

I adapted it to the width of the replica slide to be tight enough, added a fastener for the sight location and cut out the location of selector For assembly: Remove the slide from the replica, Unscrew the screw that holds the rear sight, Place the...

CAA Micro-Roni G3 - is a game ready mesh with 2 texture packs - one for Roni (4K) and the other for Glock (also 4K) for the Micro-Roni and Glock 19 models for an FPS project.

Remix of https://www.thingiverse.com/thing:4192977, made it fit on an Armorer Works VX series Hex pistol by removing the grip lines and replacing them with little knobs that slot in the hex pattern. Also enlarged the top hole so it fits over the...

... ... https://www.thingiverse.com/thing:3030223 There is a version with sights too.https://www.thingiverse.com/thing:3501100 is better to print it with abs.is not so thick because it need to fit on the roni. IF you need a diferend shape ask me about it.

...... https://www.thingiverse.com/thing:3030223 There is a version with sights too.https://www.thingiverse.com/thing:3501100 is better to print it with abs.is not so thick because it need to fit on the roni. IF you need a diferend shape ask me about it.

Nice design, Thank You Very Much, but the spring is too wimpy. Made it 5mm thicker and it now stays in place. Might need to pull it up a bit to get it in the proper position now. The tooth could be a bit thicker to stop the play. ...Maybe on the next...

Much beefier and fits like a glove

Just a normal Micro USB charging cable

Just a G39 charging handle

Charging handle by cyma replicas

latch for AR charging handle

A remix of Barrel1's charging handle

Charging handle for airsoft M249/Mk46

Extended charging handle for Ruger PCC Carbine. ...

A remix of Barrel1's charging handle

Screwless charging handle for AAP-01

charging handle for E&L replicas

charging handle for MP9 KWA AIRSOFT

charging handle ak cyma cm-520

This fits over the stock Remi 597 charging handle.

Same as the original charging handle, just a little longer.