micro titer plate 3d models
241306 3d models found related to micro titer plate.cgtrader
Name: LIAISON_ONE_TITER Version: 2013 Preview: No Units: Millimeters Dimension: 753.95 x 753.95 x 779.96 Polys: 97 112 XForm: Yes Box Trick: Yes Model Parts: 84 Render: V-Ray Formats: 3Ds Max 2013, OBJ, FBX, 3DS...
grabcad
micro limit switch plate used for fixing the micro limit switch with C BEAM profile
thingiverse
Based on openbuilds design. ...Dimensions are as in the datasheet of the micro v plate. ... No threads on the 5 central holes.
thingiverse
... Fits any micro plate with an interior diameter of 50 mm or 2 inches, and an exterior diameter of 100 mm or ~3.93 inches Tested with 5 pounds. ...Increase infill % if using more weight Supports are recommended for a cleaner finish under the handle
thingiverse
I designed it around these servos: https://willynillies.com/shop?olsPage=products%2F37g-micro-analog-servo-gh-s37a-for-rc-airplane and this Dubro pushrod kit:...
thingiverse
This is a laser cut board for attaching a Micro:bit and breadboard. ... Components: 3mm MDF 1x https://www.kitronik.co.uk/5601b-edge-connector-breakout-board-for-bbc-microbit-pre-built.html 4x spacers 1x battery strap 1x battery holder
thingiverse
designed this so that our plates for the microwave oven combi stopped falling over and laying everywhere
thingiverse
20mm X 20mm Bolt Pattern 3mm Bolt Holes 2mm Thick Plate This part is used in a micro quadcopter build that is tailored to the emax 1104 power pack. ...This specific part is used as a place to mount a FrSky SBUS Micro RX and a Hyperion Mini 600TVL AIO...
thingiverse
This fits the MinimOSD Micro within a flight controller stack. ...You have to solder the 90° angle pins.
thingiverse
I couldn't find the .stl file for the 3D printed extruder bracket that is supplied with the Micro Swiss Direct Drive extruder kit, all design rights belong to Micro Swiss, I merely reproduced it so I could print it in a choice of my colour. I also...
thingiverse
Needed a way I could bottom mount my battery on my 160mm MRM Micro Reaper so the FC screws didn't press into the battery and also wanted to secure the battery lead off the PDP so the pads didn't get ripped in a crash
thingiverse
Simple plate for the proxxon Micro-Press MP 120 -- German -- Einfache Auflage für die proxxon Micro-Press MP 120
prusaprinters
Simple plate for the proxxon Micro-Press MP 120 -- German -- Einfache Auflage für die proxxon Micro-Press MP 120 Category: Parts
thingiverse
Face Plate for the Dell Optiplex Micro 5050. ... Use 2 Mainboard screw M3 (5x7) to fasten it to the chassis.
thingiverse
The top plates are for the Spektrum VA1100 and the Walkera TX5805 Micro FPV cameras and attaches to the bottom plate with M2 nylon screws.
cults3d
Simple plate to host electronics on the Titan Dynamics Micro Trooper. Get files for Titan Dynamics planes here: https://www.titandynamics.org/3dhangar Print in any material, but LWPLA by Polylite is preferred. The holes line up with the mounting...
thingiverse
Simple plate to host electronics on the Titan Dynamics Micro Trooper. Get files for Titan Dynamics planes here: https://www.titandynamics.org/3dhangar Print in any material, but LWPLA by Polylite is preferred. The holes line up with the mounting...
thingiverse
Simple camera plate to use any Micro camera (or Nano camera with the adapter housing) on the ImpulseRC Micro Apex frame. Mirror across the x axis to make the other side. Print in PLA+, PLA, PETG, 100% infill. ...Supports optional, depends on how...
thingiverse
I bought a clone of the ImpulseRC Micro Alien frame from Unmanned Tech but the side plates used to hold the camera were a little too small which resulted in a shaky FPV feed. I took a picture of the part of my phone, converted it to .svg and the...
thingiverse
Camera mount for any Neje Micro Engraving Machine that has the yellow front plate logo. (Also includes clones.) Note: There are models out there that have a silver silk screened logo. ...You will have to use your printed part as a template to drill 4...
thingiverse
This is a replacement for the top plate and the camera mount for a uni-body micro alien frame that gives more stack space to fit a caddx vista. It also has a mount on the back that fits the antenna holder for the rush antenna that comes with the...
thingiverse
New side plates for a Leader 120 quadcopter to take a micro sized FPV camera. These plates allow a full range of angles and offer some protection for the lens. #####Notes + There are 0.5mm steps on the lugs at the bottom, I've included some...
prusaprinters
This is an adapter plate specifically for a Power HD TR-4 micro servo. It will allow the servo to bolt into a standard servo bolt pattern. The two servo mounting holes in the plate are sized to allow threading 3mm screws in to secure the...