microphone stand adapter 3d models

Microphone stand adapter to convert standard mic holder to one to support larger style, cordless microphones (35-37mm) diameter.

Adapter to mount small telescope on mic stand.

This is an adapter you can use to help replace the stock condenser-mic on a MicroKorg keyboard. ...It has standard 5/8"-28 threads for mic-stand stuff so you can put a gooseneck or whatever on it.

This is a simple little adapter that I designed so I could mount my digital wifi microscope on my boom mic stand. ...It has a 3/8-16 thread which I had to clean up with a tap after printing.

This is a M6 adapter to fit a camcorder or camera onto a standard microphone 15mm screw stand.Use two appropriate washers for each side of horizontal bolt to prevent crushing the 3d print.I made this because i had a few mic stands lying around and...

This is a 3/8 inch female to male 5/8 inch microphone stand adapter. ...It fits a ton of different stands and microphones.It includes a flat screw like cutout so you can easily tighten it.The images show the adapter on the Blue Snowball and a random...

This adapter allows you to use a microphone stand as a camera boom. ...Part of it is shaped like a microphone and the top has a 1/4-20 screw to attach to the bottom of a camera.

So I came up with an adapter that attaches the camera wall mount to the standard threads (5/8"-27 in the US) on a cheap microphone...

Inspired by musicians who use both a Green Bullet harmonica mic and SM58 dynamic microphone for vocals-- this adapter allows one to consolidate two mics onto one stand. Since the Green Bullet was originally designed to be handheld it otherwise had to...

Microphone stand adapter - 5/8 inch female - 1/4 inch male

This solution requires: - A microphone stand that with a pole that is less than or equal to 22.5 mm in diameter (hole is 23 mm). - A 1.5 inch (38.1 mm) hole saw that is capable of cutting through the material of desk. - Desktop must be no thicker...

Microphone stand can be easily removed and placed back into the desk making this solution semi-permanent. This solution requires: A microphone stand that with a pole that is less than or equal to 22.5 mm in diameter (hole is 23 mm). A 1.5 inch (38.1...

Camera tripod to microphone stand adapter Printer: Prusa i3 MK3S Printed in PLA (Sunlu) Base 70° Nozzle 200° No supports 5mm raft Fill density 40% Fill pattern: stars Steel sheet: Smooth Ventilator: all time Layer height (resolution): 0.3mm Threads:...

Camera tripod to microphone stand adapter Printer: Prusa i3 MK3S Printed in PLA (Sunlu) Base 70° Nozzle 200° No supports 5mm raft Fill density 40% Fill pattern: stars Steel sheet: Smooth Ventilator: all time Layer height (resolution): 0.3mm Threads:...

I have an old microphone stand which has 4/8 inch thread instead of commonly used 3/8 inch one so I quickly designed adapter and put M3 bolt and nut inside 3/8 thread to make it more rigid.

Needed to mount an Ion Air Pro to the top of a microphone stand using Ion's tilt adapter. Printed in PLA and chose NOT to model threads. PLA self threads nicely. if it prints loose on your printer then scale it down 5% at a time until you get a...

I wanted to put a shotgun mic on a small Manfrotto desktop tripod but could not find a suitable adapter, so I designed one. This works for me, as in: holes and threads are scaled so they printed well with my printer. Play with the scaling function of...

This adapter is meant to adapt the small 3/8"-16 screw of microphone stands to the bigger 5/8"-27 of most microphone holders. A proper metal adapter would be better, but if you have no time and you need one, this will do the job. To make...

This little model will fit onto a standard light stand, and adapt to the receiving end of a standard microphone holder. Note this only relies on friction and does not make use of the screw threads. ... Not recommended for professional use.

The 1.5cm model should fit most microphone stands, especially K&M models. (15_Mic_stand_tablet_2.stl) 1,2cm one is designed for a smaller mic stand, but I didn't need it nor print it. It can take a load of 1-2 kilos. ...I use it for the JBL control...

This is a standard 3/8'' 16 tpi (European) to 5/8'' 27tpi (US) adapter. ... You're always missing one of those.

Simple monocular adapter to microphone stand

A simple thread adapter to attach a microphone clip to a drum set cymbal stand. ...Converts the most common cymbal stand thread size (M8) to the most common microphone thread size (5/8-27).

Magnifying Glass Holder/Adapter for Microphone Stand

This is an adapter to mount the Andonstar ADSM302 microscope to a microphone stand/arm The hex opening is for a m10 nut. Most microphone arms will fit, I just replaced the imperial bolt to a metric m10 bolt on mine. Some disassembling and...

This is an adapter to mount the Andonstar ADSM302 microscope to a microphone stand/arm The hex opening is for a m10 nut. ...Most microphone arms will fit, I just replaced the imperial bolt to a metric m10 bolt on mine. Some disassembling and soldering...

I bought a LED ring with a table tripod, but I wanted to place it on a microphone stand that I had for better lightning. I've been searching here for this kind of adapter and I didn't find any, so I've designed my own, based on a couple of other...

This adapter is meant to adapt the small 1/4"-20 screw of standards camera tripods to the bigger 5/8"-27 of most microphone holders. A proper metal adapter would be better, but if you have no time and you need one, this will do the job. To make...

The desk we were using didn't have a suitable location to clamp the microphone stand to, so we designed this adapter to screw to the side of the desk and provide a good location to clamp to. Cutouts on the bottom keep the circular clamp from...

It would likely work for other clamps as well. The desk we were using didn't have a suitable location to clamp the microphone stand to, so we designed this adapter to screw to the side of the desk and provide a good location to clamp to. Cutouts on...