microscope camera adapter 3d models

In addition to the plastic parts required: 1 x Raspberry Pi Zero W 1 x Camera Module V1.3 (Sensor mounted directly on flex cable) 1 x 12mm Rod (approximately 140mm long) 1 x 5mm Rod (approximately 42mm long) 1 x 20x Macro Lens 1 x Button 4 x M3x10mm...

So I designed this adapter that you can screw onto the camera mount screw (1/4-20 UNC thread) and on the adapter you can screw the ball-joint that is on the plates for the basestations (see photo's).The fit is a bit tight, but it works and solves my...

So I designed this adapter that you can screw onto the camera mount screw (1/4-20 UNC thread) and on the adapter you can screw the ball-joint that is on the plates for the basestations (see photo's).The fit is a bit tight, but it works and solves my...

The screw tip doesn't need to press against the lens, it just needs to stop it from unscrewing from the adapter when the lens is twisted.Stop screw installed into adapter (4x magnification)Now you can line up the alignment mark on the edge of the...

I created the model to fit the Raspberry Pi camera with the original lens mount removed.I provided three different kind of lengths 3mm 6mm 9mm for different lenses, where wide angle lenses usually are quite short and need to be very close to the...

You can find them on Ali as well If you look for "smartphone led ring" I created simple adapters to connect the smartphone holder and the LED ring to a 4040 profile using t-slot nuts. There also is a clip to clamp the controller for the LED, You...

Remix of https://www.thingiverse.com/thing:5351823 Adapter for Camera Butter stick-on ND filters for GoPro Hero 9/10/11/Bones Modified to remove dark corners in 7:8 aspect ratio and to reduce reflections in bright sunlight, with added ND filter...

This is an adapter so you can use stick-on Camera Butter ND filters and Lens protectors made for the Hero 8/9 on your GepRC naked GoPro Hero 8. These are the filters to use with this adapter: https://camerabutter.com/products/gopro-hero-8-nd-filter...

I choose 12V over 5V because I plan to add a 7" LCD screen on top of the microscope, which will be connected using an HDMI cable for a larger view. These LCD screens operate at 12V, 1A, so I'm using a 12V, 2A DC adapter to ensure enough amps for...

Since I wanted to use the camera holder from https://www.thingiverse.com/thing:3950698, but had already bought a case for the Pi, an adapter plate had to be constructed for the side mounting. Since most commercial Pi cases can be fixed with a M3...

The Canon EF sensor spacing is 44mm, so I made two different lens adapter rings, one each for 17.5mm and 12.5mm cameras. The camera/filter piece is male M42x0.75 threaded to fit almost any astro camera on the market, or any t2/m42 type connection. ...

I have a budget-friendly x1000 digital microscope purchased from eBay, but it required a modified adapter to function properly. Upon realizing my desire to position it above the base plate, I essentially cut out the middle section of...

Also, if you're looking for IR filters, check out: http://on-photography.pictures/adjustable-infrared-ir-pass-filter/ For cheap action cameras to modify, visit: http://on-photography.pictures/cheap-action-cameras/ To disassemble a cheap action...

Also if your looking for IR filters check out: http://on-photography.pictures/adjustable-infrared-ir-pass-filter/ For cheap actions cameras to modify: http://on-photography.pictures/cheap-action-cameras/ How disassemble a cheap action camera:...

Post-printing steps are outlined below: Shopping List: * 2 x 4mm rods, 70mm long * 2 x 4mm rods, 60mm long * 4 x fixed M6 nuts * 2 x regular M6 nuts * 2 x 100mm M6 hinge rod * Some clear Plexiglas Stuff to Print: * 1 x microscope base of any type *...

I still use the original design for shots of smaller specimens, since it basically acts as an adapter + macro ring. I printed the whole part in 0.07 mm layers. Make sure to use black filament to avoid milky or tinted images from light passing...

This started as a simple DIY reflective microscope, but ended up as a selective wavelength microscope. Parts was designed based on thorlabs beam splitter cubes with my ideas. I have printed all the parst on Anycubic Mega Zero 2.0 I made some...

This is a simple microscope objective plate filler disc for the Swift 80 (and similar) microscopes that require a 100mm x 5mm disc on the objective stage. This print is actually 99mm in diameter to allow for tolerances in different microscopes.This...

The Cainda F210 microscope as supplied by Amazon is a very loose fit in its stand attachment ring (see image 1). This simple split spacer slides over the microscope and fills the gap. It has channels either side to help clear the control buttons...

Working with these devices, which are comparable in size to microscope slides, necessitates precise storage conditions. ...I have adjusted the width of the case to accommodate my chips, measuring 60 x 27 mm, and also uploaded a model for longer...

Human: precision microscope holder for sable2015. ... Print Settings: Rafts: disabled Supports: none required Resolution: extremely fine, 0.2 millimeters Infill: solid, 100% density

Humanity unfolds as an expansive microscope, capable of dissecting game systems and peering deeply into the inner workings of spaces within homes.

In this biology project, a microscope science model is designed using 3ds Max 2018 software. ...The visuals are rendered with V-Ray, specifically version 3.60.03.

here I designed some very basic parts of microscope. It is a completely very beginner parts. ...I just wanted to upload it in my account.

This adapter is for the Lidl Skylux telescope mount only, and user should choose appropriate wing bolt (UNC 1/4"-20) for camera or telescope attachment. Instructions on printing provided in screenshots for PP3DP users. ...Note that there may be a newer...

I created the model to fit the Raspberry Pi camera with the original lens mount removed.I provided three different kind of lengths 3mm 6mm 9mm for different lenses, where wide angle lenses usually are quite short and need to be very close to the...

if you have analog but your frame is 20mm for DJI then this will help to make it 19mm

There are two versions of the file to use. If you are using the hard plastic GoPro style mount then use the 'full width' version for a good fit. If you are using something like PTU or similar 3D printed bracket that this will fit into then the other...

This Skope microscope viewport dust cover is crafted to perfectly envelop the WF 10X viewport lens, providing a precise fit that ensures maximum protection. ...For a seamless look, consider adding a custom paint job to match your microscope's existing...

The USB cable is designed to be easily clipped to the flexible arm of the USB2 250x microscope, keeping your workspace clutter-free and allowing you to freely adjust the focus and position of the microscope with ease. ...Check out this great product at...