microsd to usb 3d models
2090972 3d models found related to microsd to usb.thingiverse
Needed a simple holder for my MicroSD to USB Adapter. Did not see one that used the two screws on the front panel. No support required if printed in the orientation shown in the last photo. ...
cults3d
Needed a simple holder for my MicroSD to USB Adapter. Did not see one that used the two screws on the front panel. ... No support required if printed in the orientation shown in the last photo.
thingiverse
Here is a different version of the MicroSD to USB Adapter Holder. I reduced the mass but increased the strength of the mounting points to reduce cracking of the filament. It should only take ~34mins if you have the infill below 10% and walls at...
cults3d
Here is a different version of the MicroSD to USB Adapter Holder. I reduced the mass but increased the strength of the mounting points to reduce cracking of the filament. It should only take ~34mins if you have the infill below 10% and walls at...
thingiverse
Purchase this microSD card to USB reader from aliexpress. The key ring pop out from reader after awhile. Found out the inner part can be pull out. This design is for holding it and add it to my key ring. ... Edit: I edit my design to add a version that...
cults3d
An updated version of my free file.
thingiverse
The cheap USB to MicroSD-Card stick that comes with the anet A2 has the following dimensions: 19mm * 7mm * 49mm It fits only to horizontal 20x20 profiles, because on the backside there are some heightenings to prevent rotation. The screw hole is for...
thingiverse
A holder for SD cards, MicroSD cards and USBs. Both the thin USBs and the full size Type As. How I Designed This I took a lot of the design from these 2 Things:http://www.thingiverse.com/thing:931121 by...
prusaprinters
This is a remix of my thing https://www.thingiverse.com/thing:2748173The rail-system is slightly simplified and within this the boxes much easier to print.the holes / guides / tunnels are designed for cable ties.for none needed holes = > i leave...
prusaprinters
This is a remix of my thing https://www.thingiverse.com/thing:2748173//////////////////////////////////////////////////////////////////////////////////// The rail-system is slightly simplified and within this the boxes much easier to print.the...
thingiverse
This is a holder-thing for the original Anet A8 MicroSD to USB Adapter. Mount it with selfadhesive tape on the Bottomside. Printable without supports. Hope you like it. ...;)
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=46335 Instructions Using the following options: Sign_FONT = orbitron Connector_Type = 1 Sign_TYPE = 1 build_plate_selector = 0 SD_gap = 3 Pencil_radius = 4 USB_Extra = 1 Pencil_gap = 3 SD_cards...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=46335 Instructions Using the following options: Device_Type = 2 Device_Order = 1 USB_gap = 5.5 Sign_TYPE = 1 build_plate_manual_y = 100 build_plate_manual_x = 100 build_plate_selector = 0...
thingiverse
A small case to add to the EasyThreed X1 to keep the USB-microSD adapter
thingiverse
This is a simple organizer for yours USB/Sd/MicroSd cards. ... It's very easy to print.
thingiverse
A simple USB-SD-micriSD holder with a small plate in the middle to keep the caps of the USB sticks. ... It can keep up to 16 USB sticks, 8 SD cards and 8 microSD.
thingiverse
Simple Phone-Stand to hold your phone and organize some USB-Sticks and/or MicroSD-Cards. I tested it using my Redmi Note 5, but it should work with most other (modern) phones. ... I included 3 files: - Just the phone-stand - The phone-stand with 4...
thingiverse
Just a smal box wiith holes for your loos USB Sticks, SD and MicroSD Cards. ...5x USB, 4x SDHC and 3x MicroSD.
thingiverse
... them all. I stuffed up the print in the photo as i didnt put enough top layers as you can see where the USB part starts building up from the MicroSD part. ... If anyone wants any changes or additions let me know and ill get it done asap cheers
thingiverse
This is a better version with more place for other thinks. ... This holder can allocate 6 wide USB sticks, 5 SD cards, and up to 5 MicroSD cards. Ideal for your desk, to keep your portable storage in a single place when you need them. ... by fentis7
pinshape
Just a simple card holder, SD/microSD/ usb. It took 2hrs and 56 min to print using the following settings. ... PLA-10%fill-2 shells-.22mm layer height-207C hot end-60C build plate-50mm extrude speed-60mm non extrude travel speed
cults3d
10x USB 5x MicroSD card 2x SD card (or MicroSD to SD adapters) The design includes holes in the bottom of all slots to keep dust and similar things from eventually building up inside of the slots, MicroSD slots are angled for easy access Just add...
thingiverse
10x USB 5x MicroSD card 2x SD card (or MicroSD to SD adapters) The design includes holes in the bottom of all slots to keep dust and similar things from eventually building up inside of the slots, MicroSD slots are angled for easy access Just add...
thingiverse
In total holds 4 USB chips, 1 SD card and 2 microSD cards. I saw a bunch of designs for holders that were had much more slots than I needed, so I decided to design a scaled back version to save some space. The indents in the design are supposed to...